The number of previous intervals for which
valid data was collected. The value will be 96
unless the interface was brought on-line within
the last 24 hours, in which case the value will
be the number of complete 15 minute intervals
the since interface has been online.
Parsed from file ncmquad.mib.txt
Company: None
Module: VERILINK-ENTERPRISE-NCMQUAD-MIB
The number of previous intervals for which
valid data was collected. The value will be 96
unless the interface was brought on-line within
the last 24 hours, in which case the value will
be the number of complete 15 minute intervals
the since interface has been online.
Parsed from file VERILINK-ENTERPRISE-NCMQUAD-MIB.mib
Module: VERILINK-ENTERPRISE-NCMQUAD-MIB
Vendor: Verilink Corp
Module: VERILINK-ENTERPRISE-NCMQUAD-MIB
[Automatically extracted from oidview.com]
ncmquadValidIntervals OBJECT-TYPE SYNTAX INTEGER (0..96) ACCESS read-only STATUS mandatory DESCRIPTION "The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online." ::= { ncmquadConfigEntry 15}
ncmquadValidIntervals OBJECT-TYPE SYNTAX INTEGER (0..96) ACCESS read-only STATUS mandatory DESCRIPTION "The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online." ::= { ncmquadConfigEntry 15}
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.321.1.3009.11000.1.1 | ncmquadLineIndex | 0 | 0 | This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with … |
| 1.3.6.1.4.1.321.1.3009.11000.1.2 | ncmquadIfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.4.1.321.1.3009.11000.1.3 | ncmquadEndId | 0 | 0 | This value for this object indicates which end of the equipment it is configuring. |
| 1.3.6.1.4.1.321.1.3009.11000.1.4 | ncmquadPort | 0 | 0 | This variable indicates Whether the port is in service or out of service |
| 1.3.6.1.4.1.321.1.3009.11000.1.5 | ncmquadLineType | 0 | 0 | This variable indicates the variety of Line implementing this circuit. The type of circuit affects the number of bits per… |
| 1.3.6.1.4.1.321.1.3009.11000.1.6 | ncmquadLineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its chara… |
| 1.3.6.1.4.1.321.1.3009.11000.1.7 | ncmquadFDL | 0 | 0 | The variable specifies the Disable/Enable of the ncmfdl State. |
| 1.3.6.1.4.1.321.1.3009.11000.1.8 | ncmquadDensityPattern | 0 | 0 | This variable indicates what type of density network is being sent on the port or line by the device. The values mean : 'Disabled… |
| 1.3.6.1.4.1.321.1.3009.11000.1.9 | ncmquadNetworkLineBuildOut | 0 | 0 | This variable indicates the db rate at which the line or port using, i.e., is 0 , -7.5db, -15db or -22.5db.[pvt] |
| 1.3.6.1.4.1.321.1.3009.11000.1.10 | ncmquadNetworkLoopConfig | 0 | 0 | This variable represents whether the device can be configured throught the network for loopback. Here values mean : Disabled: This… |
| 1.3.6.1.4.1.321.1.3009.11000.1.11 | ncmquadLineStatus | 0 | 0 | This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'a… |
| 1.3.6.1.4.1.321.1.3009.11000.1.12 | ncmquadLoopbackConfig | 0 | 0 | This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should retur… |
| 1.3.6.1.4.1.321.1.3009.11000.1.13 | ncmquadSendCode | 0 | 0 | This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: NoCode sendin… |
| 1.3.6.1.4.1.321.1.3009.11000.1.14 | ncmquadResetPerfReg | 0 | 0 | Reset Performance Monitoring registers. |
| 1.3.6.1.4.1.321.1.3009.11000.1.16 | ncmquadTimeElapsed | 0 | 0 | The number of seconds that have elapsed since the beginning of the current error-measurement period. |
| 1.3.6.1.4.1.321.1.3009.11000.1.17 | ncmquadResetT1Error | 0 | 0 | This variable indicates the option for reseting the T1 error counters. |