The variable specifies the Disable/Enable of the ncmfdl State.
Parsed from file ncmquad.mib.txt
Company: None
Module: VERILINK-ENTERPRISE-NCMQUAD-MIB
The variable specifies the Disable/Enable of the ncmfdl State.
Parsed from file VERILINK-ENTERPRISE-NCMQUAD-MIB.mib
Module: VERILINK-ENTERPRISE-NCMQUAD-MIB
Vendor: Verilink Corp
Module: VERILINK-ENTERPRISE-NCMQUAD-MIB
[Automatically extracted from oidview.com]
ncmquadFDL OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "The variable specifies the Disable/Enable of the ncmfdl State." ::= { ncmquadConfigEntry 7 }
ncmquadFDL OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "The variable specifies the Disable/Enable of the ncmfdl State." ::= { ncmquadConfigEntry 7 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.321.1.3009.11000.1.1 | ncmquadLineIndex | 0 | 0 | This object is the identifier of a Inter- face on a managed device. If there is an ifEn- try that is directly associated with … |
| 1.3.6.1.4.1.321.1.3009.11000.1.2 | ncmquadIfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.4.1.321.1.3009.11000.1.3 | ncmquadEndId | 0 | 0 | This value for this object indicates which end of the equipment it is configuring. |
| 1.3.6.1.4.1.321.1.3009.11000.1.4 | ncmquadPort | 0 | 0 | This variable indicates Whether the port is in service or out of service |
| 1.3.6.1.4.1.321.1.3009.11000.1.5 | ncmquadLineType | 0 | 0 | This variable indicates the variety of Line implementing this circuit. The type of circuit affects the number of bits per… |
| 1.3.6.1.4.1.321.1.3009.11000.1.6 | ncmquadLineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its chara… |
| 1.3.6.1.4.1.321.1.3009.11000.1.8 | ncmquadDensityPattern | 0 | 0 | This variable indicates what type of density network is being sent on the port or line by the device. The values mean : 'Disabled… |
| 1.3.6.1.4.1.321.1.3009.11000.1.9 | ncmquadNetworkLineBuildOut | 0 | 0 | This variable indicates the db rate at which the line or port using, i.e., is 0 , -7.5db, -15db or -22.5db.[pvt] |
| 1.3.6.1.4.1.321.1.3009.11000.1.10 | ncmquadNetworkLoopConfig | 0 | 0 | This variable represents whether the device can be configured throught the network for loopback. Here values mean : Disabled: This… |
| 1.3.6.1.4.1.321.1.3009.11000.1.11 | ncmquadLineStatus | 0 | 0 | This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'a… |
| 1.3.6.1.4.1.321.1.3009.11000.1.12 | ncmquadLoopbackConfig | 0 | 0 | This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should retur… |
| 1.3.6.1.4.1.321.1.3009.11000.1.13 | ncmquadSendCode | 0 | 0 | This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: NoCode sendin… |
| 1.3.6.1.4.1.321.1.3009.11000.1.14 | ncmquadResetPerfReg | 0 | 0 | Reset Performance Monitoring registers. |
| 1.3.6.1.4.1.321.1.3009.11000.1.15 | ncmquadValidIntervals | 0 | 0 | The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought o… |
| 1.3.6.1.4.1.321.1.3009.11000.1.16 | ncmquadTimeElapsed | 0 | 0 | The number of seconds that have elapsed since the beginning of the current error-measurement period. |
| 1.3.6.1.4.1.321.1.3009.11000.1.17 | ncmquadResetT1Error | 0 | 0 | This variable indicates the option for reseting the T1 error counters. |