ILMI check connection poll interval (T) in seconds.
If connectivity checking is enabled (as spec by the
value connect in the Admin_Status parameter below),
this parameter specifies the time in seconds between
successive transmissions of MIB Get msgs for the
purpose of detecting loss of ILMI connectivity. If
connectivity checking is not enabled, this parameter
must be set to zero. The default value is from the ATM
Forum ILMI Specification Version 4.0: ILMI
Connectivity Procedures (section 8.3.1).
Parsed from file stn-atm.mib.txt
Company: None
Module: STN-ATM-MIB
ILMI check connection poll interval (T) in seconds.
If connectivity checking is enabled (as spec by the
value connect in the Admin_Status parameter below),
this parameter specifies the time in seconds between
successive transmissions of MIB Get msgs for the
purpose of detecting loss of ILMI connectivity. If
connectivity checking is not enabled, this parameter
must be set to zero. The default value is from the ATM
Forum ILMI Specification Version 4.0: ILMI
Connectivity Procedures (section 8.3.1).
Parsed from file STN-ATM-MIB.mib
Module: STN-ATM-MIB
Vendor: Spring Tide Networks, Inc.
Module: STN-ATM-MIB
[Automatically extracted from oidview.com]
stnAtmPortIlmiCheckConnectionInt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "ILMI check connection poll interval (T) in seconds. If connectivity checking is enabled (as spec by the value connect in the Admin_Status parameter below), this parameter specifies the time in seconds between successive transmissions of MIB Get msgs for the purpose of detecting loss of ILMI connectivity. If connectivity checking is not enabled, this parameter must be set to zero. The default value is from the ATM Forum ILMI Specification Version 4.0: ILMI Connectivity Procedures (section 8.3.1)." DEFVAL { 5 } ::= { stnAtmPortIlmiEntry 6 }
stnAtmPortIlmiCheckConnectionInt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "ILMI check connection poll interval (T) in seconds. If connectivity checking is enabled (as spec by the value connect in the Admin_Status parameter below), this parameter specifies the time in seconds between successive transmissions of MIB Get msgs for the purpose of detecting loss of ILMI connectivity. If connectivity checking is not enabled, this parameter must be set to zero. The default value is from the ATM Forum ILMI Specification Version 4.0: ILMI Connectivity Procedures (section 8.3.1)." DEFVAL { 5 } ::= { stnAtmPortIlmiEntry 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.1 | stnAtmPortIlmiIfIndex | 0 | 0 | The interface index represents a connection point on the switch fabric from a module or line card. It is calculated based on the … |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.2 | stnAtmPortIlmiVersion | 0 | 0 | Specifies the signaling stack protocol type to be used on this port. Valid options are: uni-3-dot-0 uni-3-dot-1 uni-4-dot-0 iisp-3-d… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.3 | stnAtmPortIlmiNetworkOrientation | 0 | 0 | Specifies the ATM device type. Valid options are: user, network |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.4 | stnAtmPortIlmiAutoNegotiate | 0 | 0 | Indicates ILMI auto negotiation mode |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.5 | stnAtmPortIlmiPollInterval | 0 | 0 | ILMI connection poll interval (S) in seconds. When DC-ILMI is transmitting SNMP Get messages during the attempt to establish conn… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.7 | stnAtmPortIlmiInactivityFactor | 0 | 0 | ILMI inactivity factor (K). The number of consecutive polls for which no response is received from the remote ILMI component befo… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.8 | stnAtmPortIlmiLocalConn | 0 | 0 | Specifies whether the local end of the ILMI connection is advertised as a 'public' or 'private' ILMI device. Values are: other, pub… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.9 | stnAtmPortIlmiAdminStatus | 0 | 0 | Specifies which functions of DC-ILMI are enabled. The value std-ilmi must be specified; this value may be combined (using a bitwi… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.10 | stnAtmPortIlmiEnterprise | 0 | 0 | Enterprise Object ID that DC-ILMI will use in building SNMP traps (or other generic MIB traps). This parameter can be used to ide… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.11 | stnAtmPortIlmiLocalOid | 0 | 0 | Object ID identifying the local machine - the first 4 octets indicate the length of the object id. For example, the null object … |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.12 | stnAtmPortIlmiNetPrefix | 0 | 0 | Default network prefix. If the prefix length is non-zero, ILMI creates an entry in the ILMI NetPrefix Table for this prefix; othe… |
| 1.3.6.1.4.1.3551.2.6.1.4.2.1.1.13 | stnAtmPortIlmiPrefixLen | 0 | 0 | The length of the default network prefix |