| 1.3.6.1.4.1.9839.2.1.3.51 |
assist-sel, time-Min-Off-Freecooling-Chiller-timing, min_volt_f2, stn, defrost_t4_mm, versione_sw_hg, f7, sgl_ore_comp1, defrost_t6_dd, swrel | 0 | 0 |
0= no comp assist, 1=one comp assist, 2= two comp assist, 3... 4... |
| 1.3.6.1.4.1.9839.2.1.3.52 |
wtrvlv-sel, time-Min-Different-Freecooling-Chiller-timing, max_volt_f3, durata_pulizia, rit_acc_comp, p5, sgl_ore_comp2, defrost_t6_hh, lt_al_thrsh_al | 0 | 0 |
Water valve type 0=none, 1=chill, 2=Engy, 3=Aux chill, 4=Disc Reg |
| 1.3.6.1.4.1.9839.2.1.3.53 |
wtrvlv-volts-sel, time-Min-Same-Freecooling-Chiller-timing, triac_durat_f4, par_ora1, th, rit_spegn_comp, p9, defrost_t6_mm, sg_ore_comp, di1_config_a4 | 0 | 0 |
Water valve voltage 0= 0-10, 1=2-10, 2=7-10, 3=6-9, 4=4-7 |
| 1.3.6.1.4.1.9839.2.1.3.54 |
hum-volts, integral-Time-Freeccoling-Valve-PID, min_out_val_f7, par_ora2, tdow, p10, in_rampa_p3v, tm, hour_comp1, di2_config_a5 | 0 | 0 |
% of 10volts of analog output #2 |
| 1.3.6.1.4.1.9839.2.1.3.55 |
dehum-hours-h, derivative-Time-Freeccoling-Valve-PID, max_out_val_f8, manual_position, p11, fin_rampa_p3v, th, hour_l_comp1, comp_off_ext_a6 | 0 | 0 |
Dehumidifier Runtime - High |
| 1.3.6.1.4.1.9839.2.1.3.56 |
dehum-hours-l, output-Address-Valve-Freecooling, min_on_time_c1, posizione_valvola_perc, tempo_acc_pompa, p6, in_rampa_n3v, td, hour_comp2, tm_delay_id_a7 | 0 | 0 |
Dehumidifier Runtime - Low |
| 1.3.6.1.4.1.9839.2.1.3.57 |
delay-Freecooling-Thermal-Exclusion, min_off_time_c2, modello_valvola, h7, fin_rampa_n3v, hour_l_comp2, temp_al_del_ad | 0 | 0 |
|
| 1.3.6.1.4.1.9839.2.1.3.58 |
autoflush-dly, n-of-alarm-External-Dry-Cooler, t_betw_2_on_c3, ti_int, tempo_run, hour_comp3, cnf_di_virt_a8 | 0 | 0 |
Time between drain cycles 0=12hr, 1=24hr, 2=48hr, 3=96hr, 4=None |
| 1.3.6.1.4.1.9839.2.1.3.59 |
y4-out, delay-Alarm-Static-Pressure, t_comp_2_on_c4, ti_low, h13, rit_syson, hour_l_comp3, en_lan_di2_a9 | 0 | 0 |
Value sent to optional analog output#1 |
| 1.3.6.1.4.1.9839.2.1.3.60 |
y5-out, n-of-Alarm-Static-Pressure, t_comp_2_off_c5, tipogas, h6, hour_comp4, en_mt_al_slv_ra | 0 | 0 |
Value sent to optional analog output#2 |
| 1.3.6.1.4.1.9839.2.1.3.61 |
air-flow, delay-Warning-Static-Pressure, t_comp_fan_c7, delay_pressure_probe_alarm, h10, vr1cen, hour_l_comp4, fans_mng_f0 | 0 | 0 |
Current Fan Airflow - Based on calculated Pressure Diff formula |
| 1.3.6.1.4.1.9839.2.1.3.62 |
opt-snsr1-name, n-of-Warning-Static-Pressure, off_fan_d_fd, tipo_sonda_eva, vr2cen, hour_comp5 | 0 | 0 |
Name of the sensor |
| 1.3.6.1.4.1.9839.2.1.3.63 |
opt-sns-1-ain-type, n-of-Alarm-Differential-Pressure, on_dalay_hg, ore_mac, hour_l_comp5, fan_0_cmp_0_f2 | 0 | 0 |
Analog Sensor 1 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170} |
| 1.3.6.1.4.1.9839.2.1.3.64 |
opt-snsr2-name, priming-Time-Hydraulic-Pressure, en_rotat_c6, cmp_start_valve_position, hour_comp6, fan_0_on_def_f3 | 0 | 0 |
Name of the sensor |
| 1.3.6.1.4.1.9839.2.1.3.65 |
opt-sns-2-ain-type, delay-priming-Time-Hydraulic-Pressure, d_flow_s_p1, dd_1, ore_comp1, hour_l_comp6, fan_rele_f4 | 0 | 0 |
Analog Sensor 2 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170} |
| 1.3.6.1.4.1.9839.2.1.3.66 |
opt-snsr3-name, output-Address-Alarm-Static-Pressure, d_flow_run_p2, hh_1, ore_comp2, h_hour_fan1, tm_off_drip_fd | 0 | 0 |
Name of the sensor |
| 1.3.6.1.4.1.9839.2.1.3.67 |
opt-sns-3-ain-type, n-of-Alarm-Flow-Rate, lp_delay_p3, mm_1, h1, x_h_main_fan, l_hour_fan1 | 0 | 0 |
Analog Sensor 3 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170} |
| 1.3.6.1.4.1.9839.2.1.3.68 |
opt-snsr4-name, priming-Time-Flow-Rate, al_prb_delay_pa, dd_2, h2, x_h_valve_comp1, h_hour_fan2, relay4_mode_h1 | 0 | 0 |
Name of the sensor |
| 1.3.6.1.4.1.9839.2.1.3.69 |
opt-sns-4-ain-type, delay-priming-Time-Flow-Rate, al_gen_delay_pc, hh_2, x_h_valve_comp2, l_hour_fan2, en_dis_keyb_h2 | 0 | 0 |
Analog Sensor 4 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170} |
| 1.3.6.1.4.1.9839.2.1.3.70 |
cw-fan-speed-bms, bms-address-IDENT, t_slot_cfg_rt, mm_2, f5, h_hour_fan3, remote_control | 0 | 0 |
CW Fan speed (%) sent via BMS |
| 1.3.6.1.4.1.9839.2.1.3.71 |
dx-fan-speed-bms, fan_time_fe, dd_3, d1, l_hour_fan3 | 0 | 0 |
DX Fan speed (%) sent via BMS |
| 1.3.6.1.4.1.9839.2.1.3.72 |
fan-speed-max, abilitazione_allarme_fumo, hh_3, d2, h_hour_fan4 | 0 | 0 |
Maximum Fan speed (% of output) modulation. |
| 1.3.6.1.4.1.9839.2.1.3.73 |
fan-speed-min, abilitazione_allarme_cf, mm_3, d5, l_hour_fan4 | 0 | 0 |
Minimum Fan speed (% of output) modulation from pressure. |
| 1.3.6.1.4.1.9839.2.1.3.74 |
fan-pr-sp, abilitazione_allarme_ht, dd_4, d6, sg_ore_fan, lan_address_sa | 0 | 0 |
Fan pressure setpoint (0.01 inches of water) |
| 1.3.6.1.4.1.9839.2.1.3.75 |
fan-pr-band, hh_4, d7, version, lan_lenght_sn | 0 | 0 |
Fan pressure band (0.01 inches of water) |
| 1.3.6.1.4.1.9839.2.1.3.76 |
fan-af-max, mm_4, d8, h_hour_fan5, hh_def_sched1 | 0 | 0 |
Maximum air flow limit of setpoint from BMS or valve modulation. |
| 1.3.6.1.4.1.9839.2.1.3.77 |
fan-af-min, dd_5, d9, l_hour_fan5, mm_def_sched1 | 0 | 0 |
Minimum air flow limit of setpoint from BMS or valve modulation. |
| 1.3.6.1.4.1.9839.2.1.3.78 |
fan-kfactor, hh_5, d10, time_on_black_out, hh_def_sched2 | 0 | 0 |
Fan K Factor |
| 1.3.6.1.4.1.9839.2.1.3.79 |
num-fans, mm_5, d12, config_in1, mm_def_sched2 | 0 | 0 |
Number of fans installed in this unit |
| 1.3.6.1.4.1.9839.2.1.3.80 |
dd_6, d13, config_in2, hh_def_sched3 | 0 | 0 |
|
| 1.3.6.1.4.1.9839.2.1.3.81 |
ht2-hours-h, hh_6, config_in3, mm_def_sched3 | 0 | 0 |
Heater 2 Runtime - high |
| 1.3.6.1.4.1.9839.2.1.3.82 |
ht2-hours-l, mm_6, config_in4, hh_def_sched4 | 0 | 0 |
Heater 2 Runtime - low |
| 1.3.6.1.4.1.9839.2.1.3.83 |
ht3-hours-h, dd_7, r27, config_in5, mm_def_sched4 | 0 | 0 |
Heater 3 Runtime - high |
| 1.3.6.1.4.1.9839.2.1.3.84 |
ht3-hours-l, hh_7, l4, config_in6, hh_def_sched5 | 0 | 0 |
Heater 3 Runtime - low |
| 1.3.6.1.4.1.9839.2.1.3.85 |
engy-hours-h, mm_7, h16, config_in7, mm_def_sched5 | 0 | 0 |
Energy Saver Runtime - This optional point applies to energy saver units only -high |
| 1.3.6.1.4.1.9839.2.1.3.86 |
engy-hours-l, dd_8, p12, config_in8, hh_def_sched6 | 0 | 0 |
Energy Saver Runtime - This optional point applies to energy saver units only - low |
| 1.3.6.1.4.1.9839.2.1.3.87 |
cw-hours-h, hh_8, l1, config_in9, mm_def_sched6 | 0 | 0 |
Chilled Water Runtime - This applies to chilled water units only - high |
| 1.3.6.1.4.1.9839.2.1.3.88 |
cw-hours-l, mm_8, l2, config_in10, hh_def_sched7 | 0 | 0 |
Chilled Water Runtime - This applies to chilled water units only - low |
| 1.3.6.1.4.1.9839.2.1.3.89 |
c3-hours-h, l3, config_in11, mm_def_sched7 | 0 | 0 |
Compressor 3 Runtime - This applies when unit has four stages tandem compressors - high |
| 1.3.6.1.4.1.9839.2.1.3.90 |
c3-hours-l, l5, config_in12, hh_def_sched8 | 0 | 0 |
Compressor 3 Runtime - This applies when unit has four stages tandem compressors - low |
| 1.3.6.1.4.1.9839.2.1.3.91 |
c4-hours-l, r14, config_in13, mm_def_sched8 | 0 | 0 |
Compressor 4 Runtime - This applies when unit has four stages tandem compressors. - high |
| 1.3.6.1.4.1.9839.2.1.3.93 |
cond-hours-h, config_in15, mm_clock | 0 | 0 |
Condenser Runtime - high |
| 1.3.6.1.4.1.9839.2.1.3.94 |
cond-hours-l, config_in16, hh_vis | 0 | 0 |
Condenser Runtime - low |
| 1.3.6.1.4.1.9839.2.1.3.95 |
dx-fan-speed, config_in17, mm_vis | 0 | 0 |
Fan speed (% of output) when compressor cooling. |
| 1.3.6.1.4.1.9839.2.1.3.96 |
cw-fan-speed, config_in18 | 0 | 0 |
Fan speed (% of output) when cold water cooling. |
| 1.3.6.1.4.1.9839.2.1.3.97 |
fan-af-dx-sp, config_out1 | 0 | 0 |
Fan air flow setpoint for DX unit (cfm) |
| 1.3.6.1.4.1.9839.2.1.3.98 |
fan-af-cw-sp, config_out2 | 0 | 0 |
Fan air flow setpoint for CW unit (cfm) |
| 1.3.6.1.4.1.9839.2.1.3.99 |
zm-airflow-sp, chiller-name0, config_out3 | 0 | 0 |
Zone Airflow Setpoint kcfm |
| 1.3.6.1.4.1.9839.2.1.3.100 |
chiller-name1, config_out4 | 0 | 0 |
|
| 1.3.6.1.4.1.9839.2.1.3.101 |
config_out5 | 0 | 0 |
|