Vendor: Cascade Communications Corp.
Module: CASCADE-MIB
[Automatically extracted from oidview.com]
node OBJECT IDENTIFIER ::= { cascfr 3 }
node OBJECT IDENTIFIER ::= { cascfr 3 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.277.1.3.1 | nodeIpAddr | 1 | 1 | The inband IP address of the node in the Cascade internal trunk IP network. |
| 1.3.6.1.4.1.277.1.3.2 | nodeLanIpAddr | 1 | 1 | The inband (Ethernet) IP address of the node for a NMS to access the node and the internal trunk IP network. |
| 1.3.6.1.4.1.277.1.3.3 | nodeNMSTable | 1 | 8 | A list of NMS entries. |
| 1.3.6.1.4.1.277.1.3.4 | nodeState | 1 | 1 | The state of the switch. The switch needs to await the state to be set to active before being fully operational after cold boot, … |
| 1.3.6.1.4.1.277.1.3.5 | nodePollStatus | 1 | 1 | The consolidated node status in response to keep-alive polls. It is an octet string of a proprietary format |
| 1.3.6.1.4.1.277.1.3.6 | nodeModel | 1 | 1 | The part number of the node. |
| 1.3.6.1.4.1.277.1.3.7 | nodeSerial | 1 | 1 | The serial number (i.e., Ethernet Addr) of the switch. |
| 1.3.6.1.4.1.277.1.3.8 | nodeSwRev | 1 | 1 | The software revision number (major.minor). |
| 1.3.6.1.4.1.277.1.3.9 | nodeHwRev | 1 | 1 | The hardware revision number (major.minor). |
| 1.3.6.1.4.1.277.1.3.10 | nodeEpromRev | 1 | 1 | The EPROM firmware revision number (major.minor). |
| 1.3.6.1.4.1.277.1.3.11 | nodeCpuUtil | 1 | 1 | The CPU utilization percentage for packet processing. |
| 1.3.6.1.4.1.277.1.3.12 | nodePsAStatus | 1 | 1 | The status of the power supply A. For a detailed explanation for the power supply being either in the down or marginal state, re… |
| 1.3.6.1.4.1.277.1.3.13 | nodePsBStatus | 1 | 1 | The status of the power supply B. For a detailed explanation for the power supply being either in the down or marginal state, re… |
| 1.3.6.1.4.1.277.1.3.14 | nodeFanTable | 1 | 4 | A list of fan entries. |
| 1.3.6.1.4.1.277.1.3.15 | nodeMemoryUtil | 1 | 1 | The percentage of system memory utilization on this intelligent card. |
| 1.3.6.1.4.1.277.1.3.16 | nodeMemoryUsage | 1 | 1 | The system memory utilization, in terms of free bytes, for this intelligent card. |
| 1.3.6.1.4.1.277.1.3.17 | nodeMaxFramesize | 1 | 1 | The maximum frame size supported by the node. The default is 4096. |
| 1.3.6.1.4.1.277.1.3.18 | nodeQOSPollTimer | 1 | 1 | The timer (seconds) for generating QOS polling packets. |
| 1.3.6.1.4.1.277.1.3.19 | nodeActivePvcs | 1 | 1 | The number of currently active PVCs on the node. |
| 1.3.6.1.4.1.277.1.3.20 | nodeInactivePvcs | 1 | 1 | The number of currently inactive PVCs on the node. |
| 1.3.6.1.4.1.277.1.3.21 | nodePendingPvcs | 1 | 1 | The number of currently call pending PVCs on the node. |
| 1.3.6.1.4.1.277.1.3.22 | nodeInOctets | 1 | 1 | The total number of octets received on the node, including framing bytes. |
| 1.3.6.1.4.1.277.1.3.23 | nodeInPkts | 1 | 1 | The total number of packets received on the node. |
| 1.3.6.1.4.1.277.1.3.24 | nodeOutOctets | 1 | 1 | The total number of octets transmitted out of the node, including framing bytes. |
| 1.3.6.1.4.1.277.1.3.25 | nodeOutPkts | 1 | 1 | The total number of packets requested to be transmitted out of the node, including those that were discarded or not sent. |
| 1.3.6.1.4.1.277.1.3.26 | nodeSwFilename | 1 | 1 | Name of the file to be downloaded. |
| 1.3.6.1.4.1.277.1.3.27 | nodeRebootAfterLoad | 1 | 1 | Instructs the device to either automatically reboot after the successful scheduled download or not. |
| 1.3.6.1.4.1.277.1.3.28 | nodeSwToLoad | 1 | 1 | Instructs the device to initiate a software download (via tftp) request to the master management station after the specified time… |
| 1.3.6.1.4.1.277.1.3.29 | nodeSwLoadState | 1 | 1 | The state of the software download request. A download which is in either the PENDING, ACTIVE or FAILED state can be terminated … |
| 1.3.6.1.4.1.277.1.3.30 | nodePrFilename | 1 | 1 | Name of the PRAM image file to be downloaded. |
| 1.3.6.1.4.1.277.1.3.31 | nodePrToLoad | 1 | 1 | Instructs the device to initiate a PRAM image file download (via tftp) request to the master management station after the specifi… |
| 1.3.6.1.4.1.277.1.3.32 | nodePrLoadState | 1 | 1 | The state of the PRAM download request. A download which is in either the PENDING, ACTIVE or FAILED state can be terminated by s… |
| 1.3.6.1.4.1.277.1.3.33 | nodeToWarmboot | 1 | 1 | Instructs the switch to initiate a system warm boot after the specified time ticks have elapsed. A value of 0 indicates cancellat… |
| 1.3.6.1.4.1.277.1.3.34 | nodeToColdboot | 1 | 1 | Instructs the switch to initiate a system cold boot after the specified time ticks have elapsed. A value of 0 indicates cancellat… |
| 1.3.6.1.4.1.277.1.3.35 | nodeToRedundant | 1 | 1 | If redundancy is configured, instructs the node acting as Backup to disable the Active node and take over as the Active node. The… |
| 1.3.6.1.4.1.277.1.3.36 | nodeInitiateBulkStats | 1 | 1 | Initiates a Bulk Statistics poll and via TFTP, transfer the data to the specified IP address. |
| 1.3.6.1.4.1.277.1.3.37 | nodeDiagNonFatalSource | 1 | 1 | Source who reported last non-fatal error. |
| 1.3.6.1.4.1.277.1.3.38 | nodeDiagNonFatalTime | 1 | 1 | Time the last non-fatal error was reported. |
| 1.3.6.1.4.1.277.1.3.39 | nodeDiagNonFatalErrMajor | 1 | 1 | Major error code of last non-fatal error. |
| 1.3.6.1.4.1.277.1.3.40 | nodeDiagNonFatalErrMinor | 1 | 1 | Minor error code of last non-fatal error. |
| 1.3.6.1.4.1.277.1.3.41 | nodeDiagNonFatalStr | 1 | 1 | Ascii string describing last non-fatal error. |
| 1.3.6.1.4.1.277.1.3.42 | nodeDiagFatalSource | 1 | 1 | Source who reported last fatal error. |
| 1.3.6.1.4.1.277.1.3.43 | nodeDiagFatalTime | 1 | 1 | Time the last fatal error was reported. |
| 1.3.6.1.4.1.277.1.3.44 | nodeDiagFatalErrMajor | 1 | 1 | Major error code of last fatal error. |
| 1.3.6.1.4.1.277.1.3.45 | nodeDiagFatalErrMinor | 1 | 1 | Minor error code of last fatal error. |
| 1.3.6.1.4.1.277.1.3.46 | nodeDiagFatalStr | 1 | 1 | Ascii string describing last fatal error. |
| 1.3.6.1.4.1.277.1.3.47 | nodeDiagFatalReboots | 1 | 1 | Number of times the switch has re-booted since last fatal error was reported. |
| 1.3.6.1.4.1.277.1.3.48 | nodeDiagFatalAddress | 1 | 1 | Address switch was executing when it encountered fatal error. |
| 1.3.6.1.4.1.277.1.3.49 | nodeDiagBackgroundPasses | 1 | 1 | Number of passes made by the background diagnostics. |
| 1.3.6.1.4.1.277.1.3.50 | nodeDiagBackgroundFailures | 1 | 1 | Number of failures discovered by background diagnostics. |
| 1.3.6.1.4.1.277.1.3.51 | nodeDiagBackgroundSuccesses | 1 | 1 | Number of successful passes by background diagnostics. |
| 1.3.6.1.4.1.277.1.3.52 | nodeDiagLEDReset | 1 | 1 | Change the node state from marginal to active. Change the LED from yellow to green. |
| 1.3.6.1.4.1.277.1.3.53 | nodeDiagPowerExtensive | 1 | 1 | Should power on diagnostics do slower, extensive testing, or fast testing? |
| 1.3.6.1.4.1.277.1.3.54 | nodePortPoll | 1 | 1 | The consolidated port status in response to keep-alive polls. |
| 1.3.6.1.4.1.277.1.3.55 | nodeMaxTelnetConsole | 1 | 1 | The number of concurrent telnet consoles allowed. The default is 2. The maximum is 5. Set it 0 to disable telnet access. |
| 1.3.6.1.4.1.277.1.3.56 | nodeConsoleTimeout | 1 | 1 | Idle-logoff timer in minutes. The default is 5 minutes, and the maximum can be set is 60 minutes. To disable idle-logout, set thi… |
| 1.3.6.1.4.1.277.1.3.57 | nodeConsoleTable | 1 | 6 | A list of active consoles on the node, logged in through telnet or serial port. |
| 1.3.6.1.4.1.277.1.3.58 | nodePsADiagCode | 1 | 1 | The failure code of the power supply A. A non-zero value indicates one or more failures. Refer to the hardware manual for a des… |
| 1.3.6.1.4.1.277.1.3.59 | nodePsBDiagCode | 1 | 1 | The failure code of the power supply B. A non-zero value indicates one or more failures. Refer to the hardware manual for a des… |
| 1.3.6.1.4.1.277.1.3.60 | nodeFrameMemoryUtil | 1 | 1 | The percentage of frame memory utilization on this intelligent card. |
| 1.3.6.1.4.1.277.1.3.61 | nodeFrameMemoryUsage | 1 | 1 | The frame memory utilization, in terms of free bytes, for this intelligent card. |
| 1.3.6.1.4.1.277.1.3.62 | nodeCapability | 1 | 1 | The capability of this node. |
| 1.3.6.1.4.1.277.1.3.63 | nodeSvcLastCallFailure | 1 | 1 | A textual string describing the last call failure. |
| 1.3.6.1.4.1.277.1.3.64 | nodeRerouteDelay | 1 | 1 | The number of seconds delay between each reroute batch event. |
| 1.3.6.1.4.1.277.1.3.65 | nodeRerouteCount | 1 | 1 | The number of virtual circuits to request a reroute for duing a single reroute batch event. |
| 1.3.6.1.4.1.277.1.3.66 | nodeFileTransferRequest | 1 | 1 | This object is used to initiate file transfers to and from the switch. A management station can initiate a file transfer by settt… |
| 1.3.6.1.4.1.277.1.3.67 | nodeFileTransferStatus | 1 | 1 | The status of the file transfer. |
| 1.3.6.1.4.1.277.1.3.68 | nodeTime | 1 | 1 | The current wall-clock time that is set on the switch in Universal Coordinated Time (UCT). The value is the number of seconds si… |
| 1.3.6.1.4.1.277.1.3.69 | nodeBillingAPAddress | 1 | 1 | The IP Address of the Adjunct Billing Processor that is servicing this switch. |
| 1.3.6.1.4.1.277.1.3.70 | nodeBillingAPUsername | 1 | 1 | The Username of the account on the Adjunct Billing Processor to which usage data will be transferred via FTP. |
| 1.3.6.1.4.1.277.1.3.71 | nodeBillingAPPassword | 1 | 1 | The Password corresponding to the account identified by nodeBillingAPUsername. A NULL string is returned when read. |
| 1.3.6.1.4.1.277.1.3.72 | nodeBillingSwAPCommsFailures | 1 | 1 | The number of times that communication from the switch to the Adjunct Billing Processor has failed during the current aggregation… |
| 1.3.6.1.4.1.277.1.3.73 | nodeBillingTable | 1 | 22 | A table of Billing System managable objects, indexed by service. |
| 1.3.6.1.4.1.277.1.3.74 | nodeRerouteAlg | 1 | 1 | The number of seconds delay between each reroute batch event. |
| 1.3.6.1.4.1.277.1.3.75 | nodeADTable | 1 | 14 | A list of Authentication Domain entries. |
| 1.3.6.1.4.1.277.1.3.76 | nodeOamAlarmDisabled | 1 | 1 | If disabled then don't generate oam alarms for circuits that are down on this switch. |
| 1.3.6.1.4.1.277.1.3.77 | nodeRefclocksrcTable | 1 | 6 | A list of generators (sources) for the system reference clock on the node. This reference clock is used by the clock generation u… |
| 1.3.6.1.4.1.277.1.3.78 | nodeRefclockActiveSrc | 1 | 1 | The entry number of the active reference clock source in nodeRefclocksrcTable. If zero, the CGU is in free-running mode or holdov… |
| 1.3.6.1.4.1.277.1.3.79 | nodeRefclockActiveCGUSlotId | 1 | 1 | The physical slot id of the current master CGU board. |
| 1.3.6.1.4.1.277.1.3.80 | nodeRefclockActiveCGUMode | 1 | 1 | The clock mode of the current master CGU board. |
| 1.3.6.1.4.1.277.1.3.81 | nodeInitiateImageBackup | 1 | 1 | When set, copy all of the runtime application images and configuration images to there corresponding backup locations on the hard… |
| 1.3.6.1.4.1.277.1.3.82 | nodeImageBackupState | 1 | 1 | Provides the current state of the images backup operation. |
| 1.3.6.1.4.1.277.1.3.83 | nodeInitiateImageRestore | 1 | 1 | When set, copy all of the runtime application images and configuration images from their BACKUP locations on the hard disk to the… |
| 1.3.6.1.4.1.277.1.3.84 | nodeApplicationTable | 1 | 5 | A list of Application Image Descriptions. |
| 1.3.6.1.4.1.277.1.3.85 | nodePrimarySyncRefAdminState | 1 | 1 | The requested primary clock synchronization reference source. |
| 1.3.6.1.4.1.277.1.3.86 | nodePrimarySyncRefOperationalState | 1 | 1 | The actual primary clock synchronization reference source. |
| 1.3.6.1.4.1.277.1.3.87 | nodeSecondarySyncRefAdminState | 1 | 1 | The requested secondary clock synchronization reference source. |
| 1.3.6.1.4.1.277.1.3.88 | nodeSecondarySyncRefOperationalState | 1 | 1 | The actual secondary clock synchronization reference source. |
| 1.3.6.1.4.1.277.1.3.89 | nodePrimaryPLLOperationalState | 1 | 1 | The current state of the primary synchronization PLL. |
| 1.3.6.1.4.1.277.1.3.90 | nodeSecondaryPLLOperationalState | 1 | 1 | The current state of the secondary synchronization PLL. |
| 1.3.6.1.4.1.277.1.3.91 | nodeExternalClockAOperationalState | 1 | 1 | The current state of the External Clock A reference. |
| 1.3.6.1.4.1.277.1.3.92 | nodeExternalClockBOperationalState | 1 | 1 | The current state of the External Clock B reference. |
| 1.3.6.1.4.1.277.1.3.93 | nodePortClockAOperationalState | 1 | 1 | The current state of the Port Clock A reference. |
| 1.3.6.1.4.1.277.1.3.94 | nodePortClockBOperationalState | 1 | 1 | The current state of the Port Clock B reference. |
| 1.3.6.1.4.1.277.1.3.95 | nodeExternalTimingSource | 1 | 1 | The reference for the external timing output. |
| 1.3.6.1.4.1.277.1.3.96 | nodeSyncAutoRestore | 1 | 1 | The configuration of the Synchronization Reference Auto Restoration function. |
| 1.3.6.1.4.1.277.1.3.97 | nodeExternalClockInterfaceType | 1 | 1 | The interface type of the External Clock references. |
| 1.3.6.1.4.1.277.1.3.98 | nodeTrapMaskMib | 1 | 1 | The suppression mask for MIB II traps. |
| 1.3.6.1.4.1.277.1.3.99 | nodeTrapMaskEnterprise | 1 | 1 | The suppression mask for enterprise traps. |
| 1.3.6.1.4.1.277.1.3.100 | nodeExternalClockOutLBO | 1 | 1 | The line-build-out for the T1 External Clock Output from the switch. Default is 0-133ft. |
| 1.3.6.1.4.1.277.1.3.101 | nodeActiveTimingRefAdmin | 1 | 1 | This variable controls the indication sent to the IOMs as to which of the two clock references is preferred. Normally, it is lef… |
| 1.3.6.1.4.1.277.1.3.102 | nodeTimingManualRestore | 1 | 1 | When this variable is written, it causes the system timing hardware to attempt to revert back to the previously-failed-but-since-… |
| 1.3.6.1.4.1.277.1.3.103 | nodeLanIpMask | 1 | 1 | The inband (Ethernet) interface IP mask. the default is 255.255.255.0 |
| 1.3.6.1.4.1.277.1.3.104 | nodeBulkStatsCollectorAddress | 1 | 1 | The IP Address of the Bulk Statistics Collector to which bulk statistics data is transferred. |
| 1.3.6.1.4.1.277.1.3.105 | nodeBulkStatsTransferState | 1 | 1 | This object defines the state of a Bulk Statistics raw file transfer process to the Bulk Statistics Collector identified by the n… |
| 1.3.6.1.4.1.277.1.3.106 | nodeAuthState | 1 | 1 | Console Login Authentication for this node, enabled or disabled. |
| 1.3.6.1.4.1.277.1.3.107 | nodeAuthDomainID | 1 | 1 | Authentication Domain ID for this node. |
| 1.3.6.1.4.1.277.1.3.108 | nodeAuthFailReason | 1 | 1 | Reason for console login authentication failure. |
| 1.3.6.1.4.1.277.1.3.109 | nodeAuthLoginUser | 1 | 1 | Login user failed to pass console authentication. |
| 1.3.6.1.4.1.277.1.3.110 | nodeBulkAvgTransportBwUsed | 1 | 1 | This object reports the average amount of bandwidth (in bits per second) that has been used to transport ATM Bulk Statistics data… |
| 1.3.6.1.4.1.277.1.3.111 | nodeBulkAvgTransportBwBurst | 1 | 1 | This object reports the average transport bandwidth burst rate (in bits per second) obtained to transport ATM Bulk Statistics dat… |
| 1.3.6.1.4.1.277.1.3.112 | nodeBulkMinTransportBwBurst | 1 | 1 | This object reports the minimum transport bandwidth burst rate (in bits per second) obtained to transport ATM Bulk Statistics dat… |
| 1.3.6.1.4.1.277.1.3.113 | nodeBulkMaxTransportBwBurst | 1 | 1 | This object reports the maximum transport bandwidth burst rate (in bits per second) obtained to transport ATM Bulk Statistics dat… |
| 1.3.6.1.4.1.277.1.3.114 | nodeBulkSwAPCommsFailures | 1 | 1 | The number of times that communication from the switch to the ATM Bulk Statistics Adjunct Processor has failed during the current… |
| 1.3.6.1.4.1.277.1.3.115 | nodePsCStatus | 1 | 1 | The status of the power supply #3. For a detailed explanation for the power supply being either in the down or marginal state, r… |
| 1.3.6.1.4.1.277.1.3.116 | nodePsCDiagCode | 1 | 1 | The failure code of the power supply #3. A non-zero value indicates one or more failures. Refer to the hardware manual for a de… |
| 1.3.6.1.4.1.277.1.3.117 | nodeAdminStatus | 1 | 1 | THIS OID IS OBSOLETE. THIS CAN BE REUSED. The desired setting of the switch type indicating whether the switch has two powe… |
| 1.3.6.1.4.1.277.1.3.118 | nodeOperatingStatus | 1 | 1 | The actual switch type indicating whether the switch has two power supplies (TwoPS) or three (ThreePS). |
| 1.3.6.1.4.1.277.1.3.119 | nodeTrapSeverity | 1 | 1 | This is an OID placeholder for Trap Variables. All Cascade traps will contain this binding for the severity level of the trap. |
| 1.3.6.1.4.1.277.1.3.120 | nodeTrapSequenceNumber | 1 | 1 | This is an OID placeholder for Trap Variables. All Cascade traps will contain this binding for the sequence number of the trap. … |
| 1.3.6.1.4.1.277.1.3.121 | nodeTrapTxRate | 1 | 1 | Defines the number of traps (per second) that the switch is allowed to transmit |
| 1.3.6.1.4.1.277.1.3.122 | nodeTrapMaskSeverity | 1 | 1 | The suppression mask for trap severity levels. See nodeTrapSeverity. |
| 1.3.6.1.4.1.277.1.3.123 | nodeAlarmRelayStatus | 1 | 1 | Control of the external CO alarm relays on the SPA. |
| 1.3.6.1.4.1.277.1.3.124 | nodeTrapsDiscardedMajor | 1 | 1 | The number of Major severity traps that were discarded due to queue full conditions. |
| 1.3.6.1.4.1.277.1.3.125 | nodeTrapsDiscardedMinor | 1 | 1 | The number of Minor severity traps that were discarded due to queue full conditions. |
| 1.3.6.1.4.1.277.1.3.126 | nodeTrapDiscardedNonalarm | 1 | 1 | The number of Nonalarm severity traps that were discarded due to queue full conditions. |
| 1.3.6.1.4.1.277.1.3.127 | nodeNtpExternalPoll | 1 | 1 | The log base2 polling interval at which the active CP/SP shall request a time reference from each external reference time server,… |
| 1.3.6.1.4.1.277.1.3.128 | nodeNtpLocalPoll | 1 | 1 | The log base2 polling interval at which the IOP/IOM cards and redundant CP/SP shall request a time reference from each reference … |
| 1.3.6.1.4.1.277.1.3.129 | nodeNtpPreferredServer | 1 | 1 | The IP Address of the preferred reference time server |
| 1.3.6.1.4.1.277.1.3.130 | nodeNtpSystemStatus | 1 | 1 | The Network Timing Protocol system summary status word Leap Year Indicator 0 no warning 1 last minute has 61 sec 2 last mi… |
| 1.3.6.1.4.1.277.1.3.131 | nodeNtpSystemEventCount | 1 | 1 | System Event Counter - exceptions since last read freezes at 15 |
| 1.3.6.1.4.1.277.1.3.132 | nodeNtpSystemEventCode | 1 | 1 | System Event Code - Last Exception Code Reported |
| 1.3.6.1.4.1.277.1.3.133 | nodeNtpRefTimestampISec | 1 | 1 | nodeNtpReftimestampISec |
| 1.3.6.1.4.1.277.1.3.134 | nodeNtpRefTimeStampFSec | 1 | 1 | nodeNtpReftimeStampFSec |
| 1.3.6.1.4.1.277.1.3.135 | nodeNtpOffset | 1 | 1 | Deviation of last Ntp clock update in msec. |
| 1.3.6.1.4.1.277.1.3.136 | nodeNtpMaxOffset | 1 | 1 | Maximum Deviation between the Ntp clock msec. This value shall be cleared after it is read. |
| 1.3.6.1.4.1.277.1.3.137 | nodeNtpNumberofUpdates | 1 | 1 | Number of time the local ntp timer clock has been updated by the NTP process since startup. |
| 1.3.6.1.4.1.277.1.3.138 | nodeNtpReferenceID | 1 | 1 | This is the IP Address of the current time server being referenced |
| 1.3.6.1.4.1.277.1.3.139 | nodeBulkStatsBaseCollectPeriod | 1 | 1 | Defines the base collection period for Bulk Statistics on the B-STDX 8000/9000 starting with release 4.2. Only the following valu… |
| 1.3.6.1.4.1.277.1.3.140 | nodeLanIdleTimeout | 1 | 1 | The idle timeout interval, in seconds, for the Ethernet interface. If the Ethernet interface receives no valid IP traffic during… |
| 1.3.6.1.4.1.277.1.3.141 | nodeRelayClear | 1 | 1 | Clearing of alarm relays on the SPA. |
| 1.3.6.1.4.1.277.1.3.142 | nodeSecondaryIpAddr | 1 | 1 | Alternate address that can be used in place of nodeIPAddr when placing virtual circuits. Used when gracefully transitioning IP ne… |
| 1.3.6.1.4.1.277.1.3.143 | nodeNtpReferenceServer1 | 1 | 1 | The IP Address of the first reference time server |
| 1.3.6.1.4.1.277.1.3.144 | nodeNtpReferenceServer2 | 1 | 1 | The IP Address of the second reference time server |
| 1.3.6.1.4.1.277.1.3.145 | nodeNtpReferenceServer3 | 1 | 1 | The IP Address of the third reference time server |
| 1.3.6.1.4.1.277.1.3.146 | nodeStoredImages | 1 | 1 | Instructs the device to store the images as setA or setB to disk. |
| 1.3.6.1.4.1.277.1.3.147 | nodeRuningImages | 1 | 1 | Instructs the device to retrieve images setA or setB from disk and run them. |
| 1.3.6.1.4.1.277.1.3.148 | nodeScheduleFastLoad | 1 | 1 | To schedule software loading to happen after the specified time elapses. Software loading is the process for a switch to reload a… |
| 1.3.6.1.4.1.277.1.3.149 | nodeFastLoadStatus | 1 | 1 | The status of software loading. The value is a display string containing a status code followed by a short descriptive message. 0… |
| 1.3.6.1.4.1.277.1.3.150 | nodePwrExternalStatus | 1 | 1 | Garnet external power supply status. |
| 1.3.6.1.4.1.277.1.3.151 | nodePwrBusAStatus | 1 | 1 | Garnet 48 volt power bus A status. |
| 1.3.6.1.4.1.277.1.3.152 | nodePwrBusBStatus | 1 | 1 | Garnet 48 volt power bus B status. |
| 1.3.6.1.4.1.277.1.3.153 | nodePwrFanAStatus | 1 | 1 | Garnet 24 volt fan power supply from Timing Module A. |
| 1.3.6.1.4.1.277.1.3.154 | nodePwrFanBStatus | 1 | 1 | Garnet 24 volt fan power supply from Timing Module B. |
| 1.3.6.1.4.1.277.1.3.155 | nodeModuleTransferRequest | 1 | 1 | This object is used to initiate module download from NMS to the switch. A management station can initiate a file transfer by sett… |
| 1.3.6.1.4.1.277.1.3.156 | nodeModuleTransferStatus | 1 | 1 | The status of the module transfer. |
| 1.3.6.1.4.1.277.1.3.157 | nodeLogSrvDefIpAddr | 1 | 1 | Default IP address of the log collection station. |
| 1.3.6.1.4.1.277.1.3.158 | nodeLogDefDstDir | 1 | 1 | Default destination directory for the log files. This name must be terminated with a slash '/'. |
| 1.3.6.1.4.1.277.1.3.159 | nodeLogDefFlushTime | 1 | 1 | nodeLogDefFlushtime |
| 1.3.6.1.4.1.277.1.3.160 | nodeLogDefFlushThresh | 1 | 1 | nodeLogDefFlushthresh |
| 1.3.6.1.4.1.277.1.3.161 | nodeLogImpLevel | 1 | 1 | Importance level common to all client applications. |
| 1.3.6.1.4.1.277.1.3.162 | nodePsDcPowerAStatus | 1 | 1 | The status of the N+1 DC 48V power supply A. |
| 1.3.6.1.4.1.277.1.3.163 | nodePsDcPowerBStatus | 1 | 1 | The status of the N+1 DC 48V power supply B. |
| 1.3.6.1.4.1.277.1.3.164 | nodePTSHoldoverState | 1 | 1 | The state of the PTS holdover. |
| 1.3.6.1.4.1.277.1.3.165 | nodeOspfArea1BackCompat | 1 | 1 | This variable determines if the router can talk to pre-IP Navigator switches. |
| 1.3.6.1.4.1.277.1.3.166 | nodeMptCIR | 1 | 1 | This CIR allocated to the MPT rooted at this node. |
| 1.3.6.1.4.1.277.1.3.167 | nodeSmdsCIR | 1 | 1 | This CIR allocated to the SMDS Virtual Paths originating at this node. |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.277.1.1 | net | 29 | 62 | None |
| 1.3.6.1.4.1.277.1.2 | ase | 1 | 9 | None |
| 1.3.6.1.4.1.277.1.4 | nodePsAStatusChange, pport | 3 | 186 | None |
| 1.3.6.1.4.1.277.1.5 | nodePsBStatusChange, lport | 4 | 394 | None |
| 1.3.6.1.4.1.277.1.6 | nodeFanStatusChange, ckt | 4 | 295 | None |
| 1.3.6.1.4.1.277.1.7 | card | 9 | 254 | None |
| 1.3.6.1.4.1.277.1.8 | nodeSwDownloadFailed, cascds1, ds1 | 4 | 63 | None |
| 1.3.6.1.4.1.277.1.9 | nodePrDownloadComplete, chan | 2 | 38 | None |
| 1.3.6.1.4.1.277.1.10 | nodePrDownloadFailed, fracct | 30 | 80 | None |
| 1.3.6.1.4.1.277.1.11 | nodeTracefull | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.12 | nodeDiagLogfull | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.13 | nodeFlashMemErr | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.14 | nodePramErr | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.15 | nodeRamErr | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.16 | nodeInternalErr | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.17 | pportStatusChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.18 | lportCongests | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.19 | trkStatusChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.20 | cktDlciStatusChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.21 | cktDlciReroute | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.22 | pportInterfaceMismatch | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.23 | lportErrorExceedThreshold | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.24 | nodeErrorReport | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.25 | cktGrpStatusChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.26 | nodeUserLogin | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.27 | nodeUserLogout | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.28 | cardUp | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.29 | cardDown | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.30 | lnkStatusChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.31 | lnkSmdsHbpNaTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.32 | lnkSmdsDiscardTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.33 | cardRedundSwitchOver | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.34 | cardErrorReport | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.35 | svcSetup | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.36 | svcClearing | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.37 | svcFailure | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.38 | trkBuAttempt | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.39 | trkBuFailure | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.40 | trkBuReleased | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.41 | pportDS0LoopUpChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.42 | pportDS0LoopDownChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.43 | lportISDNCallRej | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.44 | pportdsx3LoopChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.45 | pportds1LoopChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.46 | pportExtClockBackup | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.47 | pportExtClockRestore | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.48 | pportExtClkCapabilityMismatch | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.50 | nodeBillingUsageRecOvflWarning | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.51 | nodeBillingUsageRecCrFailed | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.52 | nodeBillingStateChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.53 | lportBillingStateChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.54 | nodeBillingSwAPCommsFailure | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.57 | lportCBRLineDataError | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.58 | clkSourceSwitch | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.59 | clkSourceFailure | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.60 | lportSmdsSip3SaNotFoundTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.61 | lportSmdsSip3SaDaOnSamePortTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.62 | lportSmdsSip3DstGaNotFoundTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.63 | lportSmdsSip3DstIaScrnFailTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.64 | lportSmdsSip3SaValFailTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.65 | lportSmdsSip3DstIaNotFoundTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.66 | lportSmdsSip3SrcIaScrnFailTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.67 | lportSmdsSip3DstGaScrnFailTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.68 | lportSmdsDxi2LinkIdInvalidTca | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.69 | nodePrimarySyncReferenceChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.70 | nodeSecondarySyncReferenceChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.71 | nodeExternalClockAChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.72 | nodeExternalClockBChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.73 | nodePortReferenceAChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.74 | nodePortReferenceBChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.75 | pportDS0InitiateLpbkFailure | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.76 | pportDS0InitiateLpbkSuccess | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.77 | lportISDNIpAddrRej | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.78 | cktAtmStatusChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.79 | cktAtmReroute | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.80 | cardTransmitClockStatusChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.81 | cardSystemPrimaryClockStatusChange | 0 | 0 | None |
| 1.3.6.1.4.1.277.1.82 | cardSystemSecondaryClockStatusChange | 0 | 0 | None |