This attribute specifies the default of whether to force tagging
(CLP=1) of all cells for all CBR connections. An override to this
default may be specified for a provisioned connection under the Vcd
Tm or Vpd Tm component.
When this attribute is set to enabled, CLP is set to 1 for all cells in
the transmit direction. Force tagging is only supported on ATM IP
FPs.
On CQC-based ATM FPs, this attribute must be set to disabled.
When this attribute is set to disabled, CLP is unchanged for all cells
in the transmit direction.
This attribute never applies to any type of Vpt.
Parsed from file nortelPP-atmCoreV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-AtmCoreMIB
This attribute specifies the default of whether to force tagging
(CLP=1) of all cells for all CBR connections. An override to this
default may be specified for a provisioned connection under the Vcd
Tm or Vpd Tm component.
When this attribute is set to enabled, CLP is set to 1 for all cells in
the transmit direction. Force tagging is only supported on ATM IP
FPs.
On CQC-based ATM FPs, this attribute must be set to disabled.
When this attribute is set to disabled, CLP is unchanged for all cells
in the transmit direction.
This attribute never applies to any type of Vpt.
Parsed from file Nortel-Magellan-Passport-AtmCoreMIB.mib
Module: Nortel-Magellan-Passport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-AtmCoreMIB
[Automatically extracted from oidview.com]
atmIfCACbrForceTagging OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default of whether to force tagging (CLP=1) of all cells for all CBR connections. An override to this default may be specified for a provisioned connection under the Vcd Tm or Vpd Tm component. When this attribute is set to enabled, CLP is set to 1 for all cells in the transmit direction. Force tagging is only supported on ATM IP FPs. On CQC-based ATM FPs, this attribute must be set to disabled. When this attribute is set to disabled, CLP is unchanged for all cells in the transmit direction. This attribute never applies to any type of Vpt." DEFVAL { disabled } ::= { atmIfCACbrProvEntry 169 }
atmIfCACbrForceTagging OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default of whether to force tagging (CLP=1) of all cells for all CBR connections. An override to this default may be specified for a provisioned connection under the Vcd Tm or Vpd Tm component. When this attribute is set to enabled, CLP is set to 1 for all cells in the transmit direction. Force tagging is only supported on ATM IP FPs. On CQC-based ATM FPs, this attribute must be set to disabled. When this attribute is set to disabled, CLP is unchanged for all cells in the transmit direction. This attribute never applies to any type of Vpt." DEFVAL { disabled } ::= { atmIfCACbrProvEntry 169 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.10 | atmIfCACbrProvPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the constant bit rate (CBR) service category except f… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.20 | atmIfCACbrProvCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the CBR service category excep… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.30 | atmIfCACbrCdv | 0 | 0 | This attribute specifies the peak-to-peak cell delay variation (CDV) which is contributed to the entire ATM Interface for CBR tr… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.40 | atmIfCACbrMaxCtd | 0 | 0 | This attribute specifies the maximum cell transfer delay (MaxCTD) which is applied to the entire ATM Interface for CBR traffic. … |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.50 | atmIfCACbrProvClr | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for CBR traffic except for connections managed by a Vpt CA. The num… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.60 | atmIfCACbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the CBR service c… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.61 | atmIfCACbrHoldingPriority | 0 | 0 | This attribute specifies the holding priority which applies to SVP and SVC CBR connections. It takes a value from 0 (highest prio… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.70 | atmIfCACbrSvcHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC CBR connections. It takes a value from 0 (highest pri… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.71 | atmIfCACbrSvcMpHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC CBR point-to-multipoint connections. It takes a value… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.80 | atmIfCACbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the CBR service category. This attribut… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.90 | atmIfCACbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the CB… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.100 | atmIfCACbrEmissionPriority | 0 | 0 | This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) whi… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.140 | atmIfCACbrTrafficShaping | 0 | 0 | This attribute specifies the default traffic shaping option for connections of the CBR service category. An override to this def… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.150 | atmIfCACbrShapeRecoupPolicy | 0 | 0 | This attribute specifies the shaping recoup policy for the CBR service category. This is the policy which is used to recoup shap… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.160 | atmIfCACbrUnshapedTransmitQueueing | 0 | 0 | This attribute specifies the default queuing option for unshaped connections of the CBR service category. On ATM IP cards, this a… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.165 | atmIfCACbrWeightPolicy | 0 | 0 | This attribute specifies the default policy which is applied when calculating the fairness weight for unshaped connections of th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.170 | atmIfCACbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the CBR service category. This attr… |