This attribute specifies the default maximum queue length for the
emission queues used to buffer the traffic of the CBR service
category. It is used as the basis for setting the discard thresholds on
both common and per-VC queues. For the common queue, the
discard thresholds are set at approximately 35, 75, and 90 percent of
the value of this attribute for traffic at discard priority 3 (DP=3),
DP=2 and DP=1 respectively.
For a per-VC queue, the actual limit may be reduced depending on
the shaping rate of the connection (for standard Vpt Vccs, this is the
shaping rate of the Vpt). The discard thresholds are set at
approximately 35, 75 and 90 percent of the scaled queue limit for
traffic at discard priority 3 (DP=3), DP=2 and DP=1 respectively.
However, a reduction will never result in a value that is less than the
value set for the minPerVcQueueLimit attribute. CQC-based ATM
cards do not support per-VC queues at the CBR service category.
When this attribute is set to autoConfigure, an appropriate value is
selected based on the card type. It is set to 96 for all Passport ATM
cards (DS1, E1, IMA, JT2, DS3, E3, OC3, both CQC-based cards
and ATM IP cards).
For ATM IP FPs, the per-VC queue limit may be overridden for a
permanent connection by specifying a value in the Vcd Tm or Vpd
Tm txQueueLimit attribute.
The operational value of the maximum length of a queue (common
or per-VC) is indicated by the Vcc Tm, Vpc Tm, or Vpt Tm
txQueueThresholds attribute.
For standard Vpts, this attribute does not apply when using per-VC
queuing and only applies when using common queueing. When
using per-VC queueing, regardless of the Vpt's service category,
standard Vpts use the AtmIf Ca NrtVbr txQueueLimit value as their
default.
This attribute does not apply to basic Vpts.
VALUES (
0 = autoConfigure
)
Parsed from file nortelPP-atmCoreV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-AtmCoreMIB
This attribute specifies the default maximum queue length for the
emission queues used to buffer the traffic of the CBR service
category. It is used as the basis for setting the discard thresholds on
both common and per-VC queues. For the common queue, the
discard thresholds are set at approximately 35, 75, and 90 percent of
the value of this attribute for traffic at discard priority 3 (DP=3),
DP=2 and DP=1 respectively.
For a per-VC queue, the actual limit may be reduced depending on
the shaping rate of the connection (for standard Vpt Vccs, this is the
shaping rate of the Vpt). The discard thresholds are set at
approximately 35, 75 and 90 percent of the scaled queue limit for
traffic at discard priority 3 (DP=3), DP=2 and DP=1 respectively.
However, a reduction will never result in a value that is less than the
value set for the minPerVcQueueLimit attribute. CQC-based ATM
cards do not support per-VC queues at the CBR service category.
When this attribute is set to autoConfigure, an appropriate value is
selected based on the card type. It is set to 96 for all Passport ATM
cards (DS1, E1, IMA, JT2, DS3, E3, OC3, both CQC-based cards
and ATM IP cards).
For ATM IP FPs, the per-VC queue limit may be overridden for a
permanent connection by specifying a value in the Vcd Tm or Vpd
Tm txQueueLimit attribute.
The operational value of the maximum length of a queue (common
or per-VC) is indicated by the Vcc Tm, Vpc Tm, or Vpt Tm
txQueueThresholds attribute.
For standard Vpts, this attribute does not apply when using per-VC
queuing and only applies when using common queueing. When
using per-VC queueing, regardless of the Vpt's service category,
standard Vpts use the AtmIf Ca NrtVbr txQueueLimit value as their
default.
This attribute does not apply to basic Vpts.
VALUES (
0 = autoConfigure
)
Parsed from file Nortel-Magellan-Passport-AtmCoreMIB.mib
Module: Nortel-Magellan-Passport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-AtmCoreMIB
[Automatically extracted from oidview.com]
atmIfCACbrTxQueueLimit OBJECT-TYPE SYNTAX Unsigned32 (0 | 5..63488) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the CBR service category. It is used as the basis for setting the discard thresholds on both common and per-VC queues. For the common queue, the discard thresholds are set at approximately 35, 75, and 90 percent of the value of this attribute for traffic at discard priority 3 (DP=3), DP=2 and DP=1 respectively. For a per-VC queue, the actual limit may be reduced depending on the shaping rate of the connection (for standard Vpt Vccs, this is the shaping rate of the Vpt). The discard thresholds are set at approximately 35, 75 and 90 percent of the scaled queue limit for traffic at discard priority 3 (DP=3), DP=2 and DP=1 respectively. However, a reduction will never result in a value that is less than the value set for the minPerVcQueueLimit attribute. CQC-based ATM cards do not support per-VC queues at the CBR service category. When this attribute is set to autoConfigure, an appropriate value is selected based on the card type. It is set to 96 for all Passport ATM cards (DS1, E1, IMA, JT2, DS3, E3, OC3, both CQC-based cards and ATM IP cards). For ATM IP FPs, the per-VC queue limit may be overridden for a permanent connection by specifying a value in the Vcd Tm or Vpd Tm txQueueLimit attribute. The operational value of the maximum length of a queue (common or per-VC) is indicated by the Vcc Tm, Vpc Tm, or Vpt Tm txQueueThresholds attribute. For standard Vpts, this attribute does not apply when using per-VC queuing and only applies when using common queueing. When using per-VC queueing, regardless of the Vpt's service category, standard Vpts use the AtmIf Ca NrtVbr txQueueLimit value as their default. This attribute does not apply to basic Vpts. VALUES ( 0 = autoConfigure )" DEFVAL { 0 } ::= { atmIfCACbrProvEntry 60 }
atmIfCACbrTxQueueLimit OBJECT-TYPE SYNTAX Unsigned32 (0 | 5..63488) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the CBR service category. It is used as the basis for setting the discard thresholds on both common and per-VC queues. For the common queue, the discard thresholds are set at approximately 35, 75, and 90 percent of the value of this attribute for traffic at discard priority 3 (DP=3), DP=2 and DP=1 respectively. For a per-VC queue, the actual limit may be reduced depending on the shaping rate of the connection (for standard Vpt Vccs, this is the shaping rate of the Vpt). The discard thresholds are set at approximately 35, 75 and 90 percent of the scaled queue limit for traffic at discard priority 3 (DP=3), DP=2 and DP=1 respectively. However, a reduction will never result in a value that is less than the value set for the minPerVcQueueLimit attribute. CQC-based ATM cards do not support per-VC queues at the CBR service category. When this attribute is set to autoConfigure, an appropriate value is selected based on the card type. It is set to 96 for all Passport ATM cards (DS1, E1, IMA, JT2, DS3, E3, OC3, both CQC-based cards and ATM IP cards). For ATM IP FPs, the per-VC queue limit may be overridden for a permanent connection by specifying a value in the Vcd Tm or Vpd Tm txQueueLimit attribute. The operational value of the maximum length of a queue (common or per-VC) is indicated by the Vcc Tm, Vpc Tm, or Vpt Tm txQueueThresholds attribute. For standard Vpts, this attribute does not apply when using per-VC queuing and only applies when using common queueing. When using per-VC queueing, regardless of the Vpt's service category, standard Vpts use the AtmIf Ca NrtVbr txQueueLimit value as their default. This attribute does not apply to basic Vpts. VALUES ( 0 = autoConfigure )" DEFVAL { 0 } ::= { atmIfCACbrProvEntry 60 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.10 | atmIfCACbrProvPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the constant bit rate (CBR) service category except f… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.20 | atmIfCACbrProvCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the CBR service category excep… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.30 | atmIfCACbrCdv | 0 | 0 | This attribute specifies the peak-to-peak cell delay variation (CDV) which is contributed to the entire ATM Interface for CBR tr… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.40 | atmIfCACbrMaxCtd | 0 | 0 | This attribute specifies the maximum cell transfer delay (MaxCTD) which is applied to the entire ATM Interface for CBR traffic. … |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.50 | atmIfCACbrProvClr | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for CBR traffic except for connections managed by a Vpt CA. The num… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.61 | atmIfCACbrHoldingPriority | 0 | 0 | This attribute specifies the holding priority which applies to SVP and SVC CBR connections. It takes a value from 0 (highest prio… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.70 | atmIfCACbrSvcHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC CBR connections. It takes a value from 0 (highest pri… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.71 | atmIfCACbrSvcMpHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC CBR point-to-multipoint connections. It takes a value… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.80 | atmIfCACbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the CBR service category. This attribut… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.90 | atmIfCACbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the CB… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.100 | atmIfCACbrEmissionPriority | 0 | 0 | This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) whi… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.140 | atmIfCACbrTrafficShaping | 0 | 0 | This attribute specifies the default traffic shaping option for connections of the CBR service category. An override to this def… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.150 | atmIfCACbrShapeRecoupPolicy | 0 | 0 | This attribute specifies the shaping recoup policy for the CBR service category. This is the policy which is used to recoup shap… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.160 | atmIfCACbrUnshapedTransmitQueueing | 0 | 0 | This attribute specifies the default queuing option for unshaped connections of the CBR service category. On ATM IP cards, this a… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.165 | atmIfCACbrWeightPolicy | 0 | 0 | This attribute specifies the default policy which is applied when calculating the fairness weight for unshaped connections of th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.169 | atmIfCACbrForceTagging | 0 | 0 | This attribute specifies the default of whether to force tagging (CLP=1) of all cells for all CBR connections. An override to th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.170 | atmIfCACbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the CBR service category. This attr… |