This attribute is not applicable and is ignored for CQC-based ATM
cards.
For the 1pOC48SmSrAtm card, only the default value is supported.
For 4pOC12SmIrAtm and 4pOC12SmLrAtm cards the default
value is 2.
This attribute specifies the emission priority (EP) which is used to
transmit traffic of the rt-VBR service category. A lower numerical
value for this attribute specifies a higher emission priority. 0 is the
highest EP and 7 is the lowest. Cells at a higher emission priority
receive higher preference for link bandwidth. EPs 0 and 1 are in the
absolute priority range, and are unaffected by any minimum
bandwidth guarantees. EPs 2 through 7 are in the guaranteed
bandwidth range. Minimum bandwidth guarantee is specified in the
AtmIf/n Ep/m component.
Emission priority setting must comply with all of the following
constraints:
1. The emission priority numbers must be in the following order:
CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR
2. Two different ATM service categories may share the same EP
only if they are both shaped.
3. CBR and rt-VBR may be placed either in the absolute priority
range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2
through 7).
4. If both CBR and rt-VBR are shaped, rt-VBR must share the
same EP with CBR or ABR. If either one of CBR or rt-VBR are
not shaped, then they cannot share the same EP.
5. ABR service category is always deemed to be shaped. If nrt-VBR
is shaped, it must share the same EP with ABR. If nrt-VBR is not
shaped it must have a higher EP than ABR.
6. If UBR is shaped, it must share the same EP with ABR. If UBR
is not shaped, it must have a lower EP than ABR.
This attribute does not apply to basic Vpts, and standard Vpt Vccs.
Parsed from file nortelPC-atmCoreV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
This attribute is not applicable and is ignored for CQC-based ATM
cards.
For the 1pOC48SmSrAtm card, only the default value is supported.
For 4pOC12SmIrAtm and 4pOC12SmLrAtm cards the default
value is 2.
This attribute specifies the emission priority (EP) which is used to
transmit traffic of the rt-VBR service category. A lower numerical
value for this attribute specifies a higher emission priority. 0 is the
highest EP and 7 is the lowest. Cells at a higher emission priority
receive higher preference for link bandwidth. EPs 0 and 1 are in the
absolute priority range, and are unaffected by any minimum
bandwidth guarantees. EPs 2 through 7 are in the guaranteed
bandwidth range. Minimum bandwidth guarantee is specified in the
AtmIf/n Ep/m component.
Emission priority setting must comply with all of the following
constraints:
1. The emission priority numbers must be in the following order:
CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR
2. Two different ATM service categories may share the same EP
only if they are both shaped.
3. CBR and rt-VBR may be placed either in the absolute priority
range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2
through 7).
4. If both CBR and rt-VBR are shaped, rt-VBR must share the
same EP with CBR or ABR. If either one of CBR or rt-VBR are
not shaped, then they cannot share the same EP.
5. ABR service category is always deemed to be shaped. If nrt-VBR
is shaped, it must share the same EP with ABR. If nrt-VBR is not
shaped it must have a higher EP than ABR.
6. If UBR is shaped, it must share the same EP with ABR. If UBR
is not shaped, it must have a lower EP than ABR.
This attribute does not apply to basic Vpts, and standard Vpt Vccs.
Parsed from file Nortel-MsCarrier-MscPassport-AtmCoreMIB.mib
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
[Automatically extracted from oidview.com]
mscAtmIfCARtVbrEmissionPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is not applicable and is ignored for CQC-based ATM cards. For the 1pOC48SmSrAtm card, only the default value is supported. For 4pOC12SmIrAtm and 4pOC12SmLrAtm cards the default value is 2. This attribute specifies the emission priority (EP) which is used to transmit traffic of the rt-VBR service category. A lower numerical value for this attribute specifies a higher emission priority. 0 is the highest EP and 7 is the lowest. Cells at a higher emission priority receive higher preference for link bandwidth. EPs 0 and 1 are in the absolute priority range, and are unaffected by any minimum bandwidth guarantees. EPs 2 through 7 are in the guaranteed bandwidth range. Minimum bandwidth guarantee is specified in the AtmIf/n Ep/m component. Emission priority setting must comply with all of the following constraints: 1. The emission priority numbers must be in the following order: CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR 2. Two different ATM service categories may share the same EP only if they are both shaped. 3. CBR and rt-VBR may be placed either in the absolute priority range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2 through 7). 4. If both CBR and rt-VBR are shaped, rt-VBR must share the same EP with CBR or ABR. If either one of CBR or rt-VBR are not shaped, then they cannot share the same EP. 5. ABR service category is always deemed to be shaped. If nrt-VBR is shaped, it must share the same EP with ABR. If nrt-VBR is not shaped it must have a higher EP than ABR. 6. If UBR is shaped, it must share the same EP with ABR. If UBR is not shaped, it must have a lower EP than ABR. This attribute does not apply to basic Vpts, and standard Vpt Vccs." DEFVAL { 1 } ::= { mscAtmIfCARtVbrProvEntry 82 }
mscAtmIfCARtVbrEmissionPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is not applicable and is ignored for CQC-based ATM cards. For the 1pOC48SmSrAtm card, only the default value is supported. For 4pOC12SmIrAtm and 4pOC12SmLrAtm cards the default value is 2. This attribute specifies the emission priority (EP) which is used to transmit traffic of the rt-VBR service category. A lower numerical value for this attribute specifies a higher emission priority. 0 is the highest EP and 7 is the lowest. Cells at a higher emission priority receive higher preference for link bandwidth. EPs 0 and 1 are in the absolute priority range, and are unaffected by any minimum bandwidth guarantees. EPs 2 through 7 are in the guaranteed bandwidth range. Minimum bandwidth guarantee is specified in the AtmIf/n Ep/m component. Emission priority setting must comply with all of the following constraints: 1. The emission priority numbers must be in the following order: CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR 2. Two different ATM service categories may share the same EP only if they are both shaped. 3. CBR and rt-VBR may be placed either in the absolute priority range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2 through 7). 4. If both CBR and rt-VBR are shaped, rt-VBR must share the same EP with CBR or ABR. If either one of CBR or rt-VBR are not shaped, then they cannot share the same EP. 5. ABR service category is always deemed to be shaped. If nrt-VBR is shaped, it must share the same EP with ABR. If nrt-VBR is not shaped it must have a higher EP than ABR. 6. If UBR is shaped, it must share the same EP with ABR. If UBR is not shaped, it must have a lower EP than ABR. This attribute does not apply to basic Vpts, and standard Vpt Vccs." DEFVAL { 1 } ::= { mscAtmIfCARtVbrProvEntry 82 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.10 | mscAtmIfCARtVbrPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the real-time variable bit rate (rt-VBR) service cate… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.20 | mscAtmIfCARtVbrCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the rt-VBR service category. A… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.30 | mscAtmIfCARtVbrCdv | 0 | 0 | This attribute specifies the peak-to-peak cell delay variation (CDV) which is contributed to the entire ATM Interface for rt-VBR… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.40 | mscAtmIfCARtVbrMaxCtd | 0 | 0 | This attribute specifies the maximum cell transfer delay (MaxCTD) which is applied to the entire ATM Interface for rt-VBR traffi… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.50 | mscAtmIfCARtVbrCellLossRatio | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for rt- VBR traffic except for connections managed by a Vpt CA. The… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.60 | mscAtmIfCARtVbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the rt-VBR servi… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.70 | mscAtmIfCARtVbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the rt-VBR service category. The queue … |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.75 | mscAtmIfCARtVbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the rt… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.76 | mscAtmIfCARtVbrHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVP and SVC rt-VBR connections. It takes a value from 0 (… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.80 | mscAtmIfCARtVbrSvcHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC rt-VBR connections. It takes a value from 0 (highest … |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.81 | mscAtmIfCARtVbrSvcMpHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC rt-VBR point-to-multipoint connections. It takes a va… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.86 | mscAtmIfCARtVbrTrafficShaping | 0 | 0 | This attribute specifies the default traffic shaping option for connections of the rt-VBR service category. An override to this d… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.87 | mscAtmIfCARtVbrShapeRecoupPolicy | 0 | 0 | This attribute specifies the shaping recoup policy for the rt-VBR service category. This is the policy which is used to recoup s… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.88 | mscAtmIfCARtVbrUnshapedTransmitQueueing | 0 | 0 | This attribute specifies the default queuing option for unshaped connections of the rt-VBR service category. This attribute cont… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.89 | mscAtmIfCARtVbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the rt-VBR service category. This a… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.90 | mscAtmIfCARtVbrWeightPolicy | 0 | 0 | This attribute specifies the policy which is applied when calculating the fairness weight for unshaped connections of the rt-VBR… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.91 | mscAtmIfCARtVbrForceTagging | 0 | 0 | This attribute specifies the default of whether to force tagging (CLP=1) of all cells for all rt-VBR connections. An override to… |