This attribute specifies the default traffic shaping option for
connections of the rt-VBR service category. An override to this
default may be specified for a provisioned connection under the Vcd
Tm or Vpd Tm component.
When this attribute is set to disabled, traffic shaping cannot be
enabled for any rt-VBR connections. On 1pOC12SmLrAtm cards,
this attribute must be set to disabled.
For CQC-based ATM cards, this attribute may be set to enabled
only if the interface supports shaping, as defined by the
perVcQueueInterfaces attribute in the AtmResourceControl Cqc
Override component. If that component does not exist, this attribute
must be set to disabled.
If the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType indicates type
1 or 2, this attribute is ignored, and traffic shaping is not applicable
for that connection.
When this attribute is set to inverseUpc, traffic shaping for a
connection is enabled according to card type and the value of the
Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType. For
4pOC12SmIrAtm and 4pOC12SmLrAtm cards, inverseUpc shaping
is not available.
If this attribute is set to inverseUpc, and the txTrafficDescType is 3,
4, or 5, linear traffic shaping is enabled. Linear traffic shaping uses
a single static traffic shaping rate.
On CQC-based ATM FPs, if this attribute is set to inverseUpc, and
the txTrafficDescType is 6, 7, or 8, linear traffic shaping is enabled.
On ATM IP FPs, if this attribute is set to inverseUpc, and the
txTrafficDescType is 6, 7, or 8, inverse-UPC (also referred to as
VBR or dual leaky bucket) traffic shaping is enabled. Inverse-UPC
traffic shaping can burst above the sustained cell rate to the peak
cell rate for the duration defined by maximum burst size. Inverse-
UPC traffic shaping exactly conforms to the requirements of a dual
leaky bucket UPC enforcer.
When this attribute is set to enabled and the txTrafficDescType is 3,
4, 5, 6, 7, or 8, traffic shaping for a connection is enabled using
linear shaping.
Enabling or disabling traffic shaping may require a matching
change to the emissionPriority attribute and
unshapedTransmitQueueing attribute for this service category.
Refer to those attributes for the complete description of the
interactions.
This attribute does not apply to basic Vpts, and standard Vpt Vccs.
Parsed from file nortelPC-atmCoreV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
This attribute specifies the default traffic shaping option for
connections of the rt-VBR service category. An override to this
default may be specified for a provisioned connection under the Vcd
Tm or Vpd Tm component.
When this attribute is set to disabled, traffic shaping cannot be
enabled for any rt-VBR connections. On 1pOC12SmLrAtm cards,
this attribute must be set to disabled.
For CQC-based ATM cards, this attribute may be set to enabled
only if the interface supports shaping, as defined by the
perVcQueueInterfaces attribute in the AtmResourceControl Cqc
Override component. If that component does not exist, this attribute
must be set to disabled.
If the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType indicates type
1 or 2, this attribute is ignored, and traffic shaping is not applicable
for that connection.
When this attribute is set to inverseUpc, traffic shaping for a
connection is enabled according to card type and the value of the
Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType. For
4pOC12SmIrAtm and 4pOC12SmLrAtm cards, inverseUpc shaping
is not available.
If this attribute is set to inverseUpc, and the txTrafficDescType is 3,
4, or 5, linear traffic shaping is enabled. Linear traffic shaping uses
a single static traffic shaping rate.
On CQC-based ATM FPs, if this attribute is set to inverseUpc, and
the txTrafficDescType is 6, 7, or 8, linear traffic shaping is enabled.
On ATM IP FPs, if this attribute is set to inverseUpc, and the
txTrafficDescType is 6, 7, or 8, inverse-UPC (also referred to as
VBR or dual leaky bucket) traffic shaping is enabled. Inverse-UPC
traffic shaping can burst above the sustained cell rate to the peak
cell rate for the duration defined by maximum burst size. Inverse-
UPC traffic shaping exactly conforms to the requirements of a dual
leaky bucket UPC enforcer.
When this attribute is set to enabled and the txTrafficDescType is 3,
4, 5, 6, 7, or 8, traffic shaping for a connection is enabled using
linear shaping.
Enabling or disabling traffic shaping may require a matching
change to the emissionPriority attribute and
unshapedTransmitQueueing attribute for this service category.
Refer to those attributes for the complete description of the
interactions.
This attribute does not apply to basic Vpts, and standard Vpt Vccs.
Parsed from file Nortel-MsCarrier-MscPassport-AtmCoreMIB.mib
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
[Automatically extracted from oidview.com]
mscAtmIfCARtVbrTrafficShaping OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(5), inverseUpc(6) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default traffic shaping option for connections of the rt-VBR service category. An override to this default may be specified for a provisioned connection under the Vcd Tm or Vpd Tm component. When this attribute is set to disabled, traffic shaping cannot be enabled for any rt-VBR connections. On 1pOC12SmLrAtm cards, this attribute must be set to disabled. For CQC-based ATM cards, this attribute may be set to enabled only if the interface supports shaping, as defined by the perVcQueueInterfaces attribute in the AtmResourceControl Cqc Override component. If that component does not exist, this attribute must be set to disabled. If the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType indicates type 1 or 2, this attribute is ignored, and traffic shaping is not applicable for that connection. When this attribute is set to inverseUpc, traffic shaping for a connection is enabled according to card type and the value of the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType. For 4pOC12SmIrAtm and 4pOC12SmLrAtm cards, inverseUpc shaping is not available. If this attribute is set to inverseUpc, and the txTrafficDescType is 3, 4, or 5, linear traffic shaping is enabled. Linear traffic shaping uses a single static traffic shaping rate. On CQC-based ATM FPs, if this attribute is set to inverseUpc, and the txTrafficDescType is 6, 7, or 8, linear traffic shaping is enabled. On ATM IP FPs, if this attribute is set to inverseUpc, and the txTrafficDescType is 6, 7, or 8, inverse-UPC (also referred to as VBR or dual leaky bucket) traffic shaping is enabled. Inverse-UPC traffic shaping can burst above the sustained cell rate to the peak cell rate for the duration defined by maximum burst size. Inverse- UPC traffic shaping exactly conforms to the requirements of a dual leaky bucket UPC enforcer. When this attribute is set to enabled and the txTrafficDescType is 3, 4, 5, 6, 7, or 8, traffic shaping for a connection is enabled using linear shaping. Enabling or disabling traffic shaping may require a matching change to the emissionPriority attribute and unshapedTransmitQueueing attribute for this service category. Refer to those attributes for the complete description of the interactions. This attribute does not apply to basic Vpts, and standard Vpt Vccs." DEFVAL { disabled } ::= { mscAtmIfCARtVbrProvEntry 86 }
mscAtmIfCARtVbrTrafficShaping OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(5), inverseUpc(6) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default traffic shaping option for connections of the rt-VBR service category. An override to this default may be specified for a provisioned connection under the Vcd Tm or Vpd Tm component. When this attribute is set to disabled, traffic shaping cannot be enabled for any rt-VBR connections. On 1pOC12SmLrAtm cards, this attribute must be set to disabled. For CQC-based ATM cards, this attribute may be set to enabled only if the interface supports shaping, as defined by the perVcQueueInterfaces attribute in the AtmResourceControl Cqc Override component. If that component does not exist, this attribute must be set to disabled. If the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType indicates type 1 or 2, this attribute is ignored, and traffic shaping is not applicable for that connection. When this attribute is set to inverseUpc, traffic shaping for a connection is enabled according to card type and the value of the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType. For 4pOC12SmIrAtm and 4pOC12SmLrAtm cards, inverseUpc shaping is not available. If this attribute is set to inverseUpc, and the txTrafficDescType is 3, 4, or 5, linear traffic shaping is enabled. Linear traffic shaping uses a single static traffic shaping rate. On CQC-based ATM FPs, if this attribute is set to inverseUpc, and the txTrafficDescType is 6, 7, or 8, linear traffic shaping is enabled. On ATM IP FPs, if this attribute is set to inverseUpc, and the txTrafficDescType is 6, 7, or 8, inverse-UPC (also referred to as VBR or dual leaky bucket) traffic shaping is enabled. Inverse-UPC traffic shaping can burst above the sustained cell rate to the peak cell rate for the duration defined by maximum burst size. Inverse- UPC traffic shaping exactly conforms to the requirements of a dual leaky bucket UPC enforcer. When this attribute is set to enabled and the txTrafficDescType is 3, 4, 5, 6, 7, or 8, traffic shaping for a connection is enabled using linear shaping. Enabling or disabling traffic shaping may require a matching change to the emissionPriority attribute and unshapedTransmitQueueing attribute for this service category. Refer to those attributes for the complete description of the interactions. This attribute does not apply to basic Vpts, and standard Vpt Vccs." DEFVAL { disabled } ::= { mscAtmIfCARtVbrProvEntry 86 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.10 | mscAtmIfCARtVbrPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the real-time variable bit rate (rt-VBR) service cate… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.20 | mscAtmIfCARtVbrCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the rt-VBR service category. A… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.30 | mscAtmIfCARtVbrCdv | 0 | 0 | This attribute specifies the peak-to-peak cell delay variation (CDV) which is contributed to the entire ATM Interface for rt-VBR… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.40 | mscAtmIfCARtVbrMaxCtd | 0 | 0 | This attribute specifies the maximum cell transfer delay (MaxCTD) which is applied to the entire ATM Interface for rt-VBR traffi… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.50 | mscAtmIfCARtVbrCellLossRatio | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for rt- VBR traffic except for connections managed by a Vpt CA. The… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.60 | mscAtmIfCARtVbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the rt-VBR servi… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.70 | mscAtmIfCARtVbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the rt-VBR service category. The queue … |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.75 | mscAtmIfCARtVbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the rt… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.76 | mscAtmIfCARtVbrHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVP and SVC rt-VBR connections. It takes a value from 0 (… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.80 | mscAtmIfCARtVbrSvcHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC rt-VBR connections. It takes a value from 0 (highest … |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.81 | mscAtmIfCARtVbrSvcMpHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC rt-VBR point-to-multipoint connections. It takes a va… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.82 | mscAtmIfCARtVbrEmissionPriority | 0 | 0 | This attribute is not applicable and is ignored for CQC-based ATM cards. For the 1pOC48SmSrAtm card, only the default value is s… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.87 | mscAtmIfCARtVbrShapeRecoupPolicy | 0 | 0 | This attribute specifies the shaping recoup policy for the rt-VBR service category. This is the policy which is used to recoup s… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.88 | mscAtmIfCARtVbrUnshapedTransmitQueueing | 0 | 0 | This attribute specifies the default queuing option for unshaped connections of the rt-VBR service category. This attribute cont… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.89 | mscAtmIfCARtVbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the rt-VBR service category. This a… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.90 | mscAtmIfCARtVbrWeightPolicy | 0 | 0 | This attribute specifies the policy which is applied when calculating the fairness weight for unshaped connections of the rt-VBR… |
| 1.3.6.1.4.1.562.36.2.1.114.3.3.100.1.91 | mscAtmIfCARtVbrForceTagging | 0 | 0 | This attribute specifies the default of whether to force tagging (CLP=1) of all cells for all rt-VBR connections. An override to… |