This attribute specifies the type of ABR behavior which is to be
enforced at this connection. This attribute is only applicable if the
atmServiceCategory attribute is availableBitRate. If the
atmServicecategory attribute is not availableBitRate, this attribute
value is ignored.
The actual ABR functionality which is in effect is visible in the
Vcc/Vpc/Vpt Tm abrConnectionType operational attribute.
For CQC-based ATM cards, the only allowable values are
sameAsCa, nonAbrInterworking or abrSwitch. If abrSwitch is
selected, the CQC implements EFCI marking behavior.
For the 1pOC12SmLrAtm card, the only allowable values are
sameAsCa or abrSwitch. If abrSwitch is selected, EFCI marking
behavior is implemented.
sameAsCa is used to request the default behavior as specified in the
CA Abr component for this Vcc. Otherwise, this attribute overrides
the default behavior.
virtualSourceDest is used to request that this connection point
function as a virtual source/virtual destination. VS/VD functionality
is only supported on ATM IP FPs.
sourceDest requires that this connection point function as a S/D for
RM cells. S/D mode is automatically invoked at this connection
point either if this is a connection end point, or if the next hop
connection point is configured as nonAbrInterworking.
nonAbrInterworking is used to request that this connection point
function as an interworking between ABR and non-ABR service
categories. This means that there are no RM cells on the link side of
this connection, and that the next hop connection point is
performing as an ABR sourceDest.
abrSwitch is used to request ABR switch behavior for this
connection point. The ABR switch behavior is first, to confirm to
virtualSourceDest or nonAbrInterworking setting on the next hop,
and otherwise to implement ABR ER switch behavior. For CQC-
based FPs, ABR switch behavior is implemented as EFCI marking.
Parsed from file nortelPC-atmCoreV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
This attribute specifies the type of ABR behavior which is to be
enforced at this connection. This attribute is only applicable if the
atmServiceCategory attribute is availableBitRate. If the
atmServicecategory attribute is not availableBitRate, this attribute
value is ignored.
The actual ABR functionality which is in effect is visible in the
Vcc/Vpc/Vpt Tm abrConnectionType operational attribute.
For CQC-based ATM cards, the only allowable values are
sameAsCa, nonAbrInterworking or abrSwitch. If abrSwitch is
selected, the CQC implements EFCI marking behavior.
For the 1pOC12SmLrAtm card, the only allowable values are
sameAsCa or abrSwitch. If abrSwitch is selected, EFCI marking
behavior is implemented.
sameAsCa is used to request the default behavior as specified in the
CA Abr component for this Vcc. Otherwise, this attribute overrides
the default behavior.
virtualSourceDest is used to request that this connection point
function as a virtual source/virtual destination. VS/VD functionality
is only supported on ATM IP FPs.
sourceDest requires that this connection point function as a S/D for
RM cells. S/D mode is automatically invoked at this connection
point either if this is a connection end point, or if the next hop
connection point is configured as nonAbrInterworking.
nonAbrInterworking is used to request that this connection point
function as an interworking between ABR and non-ABR service
categories. This means that there are no RM cells on the link side of
this connection, and that the next hop connection point is
performing as an ABR sourceDest.
abrSwitch is used to request ABR switch behavior for this
connection point. The ABR switch behavior is first, to confirm to
virtualSourceDest or nonAbrInterworking setting on the next hop,
and otherwise to implement ABR ER switch behavior. For CQC-
based FPs, ABR switch behavior is implemented as EFCI marking.
Parsed from file Nortel-MsCarrier-MscPassport-AtmCoreMIB.mib
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
[Automatically extracted from oidview.com]
mscAtmIfVccVcdTmAbrConnectionType OBJECT-TYPE SYNTAX INTEGER { abrSwitch(0), virtualSourceDest(3), sourceDest(4), nonAbrInterworking(5), sameAsCa(14) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of ABR behavior which is to be enforced at this connection. This attribute is only applicable if the atmServiceCategory attribute is availableBitRate. If the atmServicecategory attribute is not availableBitRate, this attribute value is ignored. The actual ABR functionality which is in effect is visible in the Vcc/Vpc/Vpt Tm abrConnectionType operational attribute. For CQC-based ATM cards, the only allowable values are sameAsCa, nonAbrInterworking or abrSwitch. If abrSwitch is selected, the CQC implements EFCI marking behavior. For the 1pOC12SmLrAtm card, the only allowable values are sameAsCa or abrSwitch. If abrSwitch is selected, EFCI marking behavior is implemented. sameAsCa is used to request the default behavior as specified in the CA Abr component for this Vcc. Otherwise, this attribute overrides the default behavior. virtualSourceDest is used to request that this connection point function as a virtual source/virtual destination. VS/VD functionality is only supported on ATM IP FPs. sourceDest requires that this connection point function as a S/D for RM cells. S/D mode is automatically invoked at this connection point either if this is a connection end point, or if the next hop connection point is configured as nonAbrInterworking. nonAbrInterworking is used to request that this connection point function as an interworking between ABR and non-ABR service categories. This means that there are no RM cells on the link side of this connection, and that the next hop connection point is performing as an ABR sourceDest. abrSwitch is used to request ABR switch behavior for this connection point. The ABR switch behavior is first, to confirm to virtualSourceDest or nonAbrInterworking setting on the next hop, and otherwise to implement ABR ER switch behavior. For CQC- based FPs, ABR switch behavior is implemented as EFCI marking." DEFVAL { sameAsCa } ::= { mscAtmIfVccVcdTmProvEntry 90 }
mscAtmIfVccVcdTmAbrConnectionType OBJECT-TYPE SYNTAX INTEGER { abrSwitch(0), virtualSourceDest(3), sourceDest(4), nonAbrInterworking(5), sameAsCa(14) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the type of ABR behavior which is to be enforced at this connection. This attribute is only applicable if the atmServiceCategory attribute is availableBitRate. If the atmServicecategory attribute is not availableBitRate, this attribute value is ignored. The actual ABR functionality which is in effect is visible in the Vcc/Vpc/Vpt Tm abrConnectionType operational attribute. For CQC-based ATM cards, the only allowable values are sameAsCa, nonAbrInterworking or abrSwitch. If abrSwitch is selected, the CQC implements EFCI marking behavior. For the 1pOC12SmLrAtm card, the only allowable values are sameAsCa or abrSwitch. If abrSwitch is selected, EFCI marking behavior is implemented. sameAsCa is used to request the default behavior as specified in the CA Abr component for this Vcc. Otherwise, this attribute overrides the default behavior. virtualSourceDest is used to request that this connection point function as a virtual source/virtual destination. VS/VD functionality is only supported on ATM IP FPs. sourceDest requires that this connection point function as a S/D for RM cells. S/D mode is automatically invoked at this connection point either if this is a connection end point, or if the next hop connection point is configured as nonAbrInterworking. nonAbrInterworking is used to request that this connection point function as an interworking between ABR and non-ABR service categories. This means that there are no RM cells on the link side of this connection, and that the next hop connection point is performing as an ABR sourceDest. abrSwitch is used to request ABR switch behavior for this connection point. The ABR switch behavior is first, to confirm to virtualSourceDest or nonAbrInterworking setting on the next hop, and otherwise to implement ABR ER switch behavior. For CQC- based FPs, ABR switch behavior is implemented as EFCI marking." DEFVAL { sameAsCa } ::= { mscAtmIfVccVcdTmProvEntry 90 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.10 | mscAtmIfVccVcdTmTxTrafficDescType | 0 | 0 | This attribute specifies the type of traffic management which is applied to the transmit direction of this connection as defined… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.21 | mscAtmIfVccVcdTmFwdQosClass | 0 | 0 | This attribute specifies the quality of service for the forward direction for this connection. This attribute is only used for S… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.22 | mscAtmIfVccVcdTmTxQueueLimit | 0 | 0 | This attribute specifies an override to the default transmit queue limit for this connection. An value other than sameAsCa may b… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.25 | mscAtmIfVccVcdTmHoldingPriority | 0 | 0 | This attribute specifies the holding priority of this connection. In a situation where the link bandwidth fluctuates, such as ov… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.30 | mscAtmIfVccVcdTmRxTrafficDescType | 0 | 0 | This attribute specifies the type of traffic management which is applied to the receive direction of this connection as defined … |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.41 | mscAtmIfVccVcdTmBwdQosClass | 0 | 0 | This attribute specifies the quality of service for the backward direction for this connection. This attribute is only used for … |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.42 | mscAtmIfVccVcdTmAtmServiceCategory | 0 | 0 | This attribute specifies the ATM service category for both directions of the connection. The value derivedFromBBC may only be us… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.50 | mscAtmIfVccVcdTmTrafficShaping | 0 | 0 | This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. This attri… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.60 | mscAtmIfVccVcdTmUnshapedTransmitQueueing | 0 | 0 | This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this con… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.61 | mscAtmIfVccVcdTmWeight | 0 | 0 | This attribute specifies an override for the weight of this unshaped connection. This attribute is ignored for shaped connection… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.62 | mscAtmIfVccVcdTmForceTagging | 0 | 0 | This attribute specifies whether force tagging is enforced for this connection for cells in the transmit direction. On CQC-based… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.70 | mscAtmIfVccVcdTmUsageParameterControl | 0 | 0 | This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface.… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.71 | mscAtmIfVccVcdTmBearerClassBbc | 0 | 0 | This attribute specifies the bearer capability. This attribute is only used for SPVC and SPVP connections. It is one of the Broa… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.72 | mscAtmIfVccVcdTmTransferCapabilityBbc | 0 | 0 | This attribute specifies the transfer capability for this connection. Uni 3.0/3.1 traffic type and end-to-end timing parameters … |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.74 | mscAtmIfVccVcdTmClippingBbc | 0 | 0 | This attribute specifies the value for the clipping susceptibility parameter in the BBC Information Element. This attribute is o… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.75 | mscAtmIfVccVcdTmBestEffort | 0 | 0 | This attribute specifies the value of the best effort parameter in the ATM Traffic Descriptor Information Element. This attribut… |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.76 | mscAtmIfVccVcdTmTxPacketWiseDiscard | 0 | 0 | This attribute specifies whether packet-wise discard functions are to be enabled or disabled in the transmit data direction for … |
1.3.6.1.4.1.562.36.2.1.114.5.2.2.100.1.78 | mscAtmIfVccVcdTmRxPacketWiseDiscard | 0 | 0 | This attribute specifies whether packet-wise discard functions are to be enabled or disabled in the receive data direction for t… |