The MIB for managing Signalling Points and its
associated messages transported over Signalling
System No. 7 (SS7) Network via Cisco IP Transfer
Point.
The Cisco IP Transfer Point (ITP) is a hardware
and software solution that transports SS7 traffic
using IP. Each ITP node provides function similar
to SS7 Signalling point.
The relevant ITU documents describing this technology
is the ITU Q series, including ITU Q.700: Introduction
to CCITT Signalling System No. 7 and ITU Q.701
Functional description of the message transfer part
(MTP) of Signalling System No. 7.
This MIB models the SP as follows:
The SP is associated with one or more point codes.
Each pointcode is associated with:
an SS7 variant, timers, and linksets.
Linksets contain:
destination point code
linkset byte/packet statistics,
accounting information per Destination Point
Code(DPC) and Originating Point Code (OPC)
violation accounting information per DPC and OPC
links, reference to incoming and outgoing ACL
reference to a routing table for each SS7 packet type
Links contain:
timers, and byte/packet statistics.
The figure below provides a diagrammatic representation
of the relationships. Each box may be replicated
providing multiple instances of the object.
'
a reference to the object to the right.
'###>' indicates that the object to the left contains
an instance of the object to the right.
The down arrow indicates that the object being pointed
to contains snmp indices of the objects above it.
________________
| |
| Sp |###> point code, timers
|________________|
|
V
________________
| |
| |
| Linkset |
| |
| |
|________________|
|
V
________________
| Link |###> timers
|________________|
Abbreviations:
AERM - Alignment Error Rate Monitor
CLLI - Common Language Location Codes
HSL - High Speed Link (ATM based)
LLSC - link set control
LSAC - Signalling link activity control
LSDA - Signalling data link allocation
LSLA - Signalling link activation
LSLD - Signalling link deactivation
LSLR - Signalling link restoration
LSSU - Link Status Signal Unit
LSTA - Signalling terminal allocation
MTP - Message Transport Protocol
MTP2 - Layer 2 of Message Transport Protocol
MTP3 - Layer 3 of Message Transport Protocol
PC - Point Code
RTN - RouteTableName
SCTP - Stream Transmission Protocol(RFC 2960)
SIB - Status Indicator Busy
SP - Signalling Point
SS7 - System No. 7 (SS7) Network
SUERM - Signal Unit Error Rate Monitor
TCBC - Changeback control
TCOC - Changeover control
TCRC - Controlled rerouting control
TFRC - Forced rerouting control
TLAC - Link availability control
TPRC - Signalling point restart control
TRCC - Signalling route set congestion control
TSFC - Signalling traffic flow control
TSRC - Signalling routing control
The MIB for managing Signalling Points and its
associated messages transported over Signalling
System No. 7 (SS7) Network via Cisco IP Transfer
Point.
The Cisco IP Transfer Point (ITP) is a hardware
and software solution that transports SS7 traffic
using IP. Each ITP node provides function similar
to SS7 Signalling point.
The relevant ITU documents describing this technology
is the ITU Q series, including ITU Q.700: Introduction
to CCITT Signalling System No. 7 and ITU Q.701
Functional description of the message transfer part
(MTP) of Signalling System No. 7.
This MIB models the SP as follows:
The SP is associated with one or more point codes.
Each pointcode is associated with:
an SS7 variant, timers, and linksets.
Linksets contain:
destination point code
linkset byte/packet statistics,
accounting information per Destination Point
Code(DPC) and Originating Point Code (OPC)
violation accounting information per DPC and OPC
links, reference to incoming and outgoing ACL
reference to a routing table for each SS7 packet type
Links contain:
timers, and byte/packet statistics.
The figure below provides a diagrammatic representation
of the relationships. Each box may be replicated
providing multiple instances of the object.
'
a reference to the object to the right.
'###>' indicates that the object to the left contains
an instance of the object to the right.
The down arrow indicates that the object being pointed
to contains snmp indices of the objects above it.
________________
| |
| Sp |###> point code, timers
|________________|
|
V
________________
| |
| |
| Linkset |
| |
| |
|________________|
|
V
________________
| Link |###> timers
|________________|
Abbreviations:
AERM - Alignment Error Rate Monitor
CLLI - Common Language Location Codes
HSL - High Speed Link (ATM based)
LLSC - link set control
LSAC - Signalling link activity control
LSDA - Signalling data link allocation
LSLA - Signalling link activation
LSLD - Signalling link deactivation
LSLR - Signalling link restoration
LSSU - Link Status Signal Unit
LSTA - Signalling terminal allocation
MTP - Message Transport Protocol
MTP2 - Layer 2 of Message Transport Protocol
MTP3 - Layer 3 of Message Transport Protocol
PC - Point Code
RTN - RouteTableName
SCTP - Stream Transmission Protocol(RFC 2960)
SIB - Status Indicator Busy
SP - Signalling Point
SS7 - System No. 7 (SS7) Network
SUERM - Signal Unit Error Rate Monitor
TCBC - Changeback control
TCOC - Changeover control
TCRC - Controlled rerouting control
TFRC - Forced rerouting control
TLAC - Link availability control
TPRC - Signalling point restart control
TRCC - Signalling route set congestion control
TSFC - Signalling traffic flow control
TSRC - Signalling routing control
Parsed from file CISCO-ITP-SP-MIB.mib
Module: CISCO-ITP-SP-MIB
ciscoItpSpMIB MODULE-IDENTITY LAST-UPDATED "200302180000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems, Inc Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the SP as follows: The SP is associated with one or more point codes. Each pointcode is associated with: an SS7 variant, timers, and linksets. Linksets contain: destination point code linkset byte/packet statistics, accounting information per Destination Point Code(DPC) and Originating Point Code (OPC) violation accounting information per DPC and OPC links, reference to incoming and outgoing ACL reference to a routing table for each SS7 packet type Links contain: timers, and byte/packet statistics. The figure below provides a diagrammatic representation of the relationships. Each box may be replicated providing multiple instances of the object. ' a reference to the object to the right. '###>' indicates that the object to the left contains an instance of the object to the right. The down arrow indicates that the object being pointed to contains snmp indices of the objects above it. ________________ | | | Sp |###> point code, timers |________________| | V ________________ | | | | | Linkset | | | | | |________________| | V ________________ | Link |###> timers |________________| Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common Language Location Codes HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control " REVISION "200302180000Z" DESCRIPTION "The ability to allow multiple instances of Signalling Points to run in the same device has introduce a new index structure. All objects in this MIB will be deprecated and replaced by objects in the CISCO-ITP-GSP-MIB.my MIB." REVISION "200203070000Z" DESCRIPTION "Added support for notification on link utilization. Textual conventions: CItpSpSampleInterval CItpSpPercentThreshold CItpSpLinkUtilization CItpSpLinkCapacity CItpSpLinkUtilizationState Scalars: cItpSpUtilSampleInterval cItpSpUtilThreshold cItpSpUtilAbateDelta Linkset table: cItpSpLinksetPlanCapacity - deprecated. Link table: cItpSpLinkPlanCapacityRcvd cItpSpLinkUtilThresholdRcvd cItpSpLinkUtilizationRcvd cItpSpLinkUtilStateRcvd cItpSpLinkL2BytesRcvd cItpSpLinkPlanCapacitySent cItpSpLinkUtilThresholdSent cItpSpLinkUtilizationSent cItpSpLinkUtilStateSent cItpSpLinkL2BytesSent Notification enable: cItpSpLinkUtilNotifEnabled Notification: cItpSpLinkRcvdUtilChange cItpSpLinkSentUtilChange" REVISION "200201230000Z" DESCRIPTION "Modified the following objects: cItpSpLinkType: Added new high speed link type to textual convention CItpTcLinkType. cItpSpVariant: Added new China SS7 variant to textual convention CItpTcSs7Variant. Add new enumerate Added the following objects: cItpSpDistSccpUnseq cItpSpSummaryRoutingException cItpSpLinksetVariant cItpSpLinkDroppedPkts cItpSpLinkTransmittedLssu cItpSpLinkReceivedLssu cItpSpLinkProtocolDetails cItpSpLinkLsacState cItpSpLinkTsrcState cItpSpLinkTcocState cItpSpLinkTcocLocalBSNT cItpSpLinkTcocRemoteBSNT cItpSpLinkTcbcState cItpSpLinkReceivedSIB cItpSpLinkTransmittedSIB cItpSpLinkMtp2ExpiredT01 cItpSpLinkMtp2ExpiredT02 cItpSpLinkMtp2ExpiredT03 cItpSpLinkMtp2ExpiredT04 cItpSpLinkMtp2ExpiredT05 cItpSpLinkMtp2ExpiredT06 cItpSpLinkMtp2ExpiredT07 cItpSpLinkOMAERMCount cItpSpLinkOMAERMFailCount cItpSpLinkOMSURMCount cItpSpLinkOMSURMFailCount" REVISION "200108290000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 232 }
ciscoItpSpMIB OBJECT IDENTIFIER ::= { ciscoMgmt 232 }
Vendor: Cisco
Module: CISCO-ITP-SP-MIB
[Automatically extracted from oidview.com]
ciscoItpSpMIB OBJECT IDENTIFIER ::= { ciscoMgmt 232 }
ciscoItpSpMIB MODULE-IDENTITY LAST-UPDATED "200302180000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems, Inc Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the SP as follows: The SP is associated with one or more point codes. Each pointcode is associated with: an SS7 variant, timers, and linksets. Linksets contain: destination point code linkset byte/packet statistics, accounting information per Destination Point Code(DPC) and Originating Point Code (OPC) violation accounting information per DPC and OPC links, reference to incoming and outgoing ACL reference to a routing table for each SS7 packet type Links contain: timers, and byte/packet statistics. The figure below provides a diagrammatic representation of the relationships. Each box may be replicated providing multiple instances of the object. ' a reference to the object to the right. '###>' indicates that the object to the left contains an instance of the object to the right. The down arrow indicates that the object being pointed to contains snmp indices of the objects above it. ________________ | | | Sp |###> point code, timers |________________| | V ________________ | | | | | Linkset | | | | | |________________| | V ________________ | Link |###> timers |________________| Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common Language Location Codes HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control " REVISION "200302180000Z" DESCRIPTION "The ability to allow multiple instances of Signalling Points to run in the same device has introduce a new index structure. All objects in this MIB will be deprecated and replaced by objects in the CISCO-ITP-GSP-MIB.my MIB." REVISION "200203070000Z" DESCRIPTION "Added support for notification on link utilization. Textual conventions: CItpSpSampleInterval CItpSpPercentThreshold CItpSpLinkUtilization CItpSpLinkCapacity CItpSpLinkUtilizationState Scalars: cItpSpUtilSampleInterval cItpSpUtilThreshold cItpSpUtilAbateDelta Linkset table: cItpSpLinksetPlanCapacity - deprecated. Link table: cItpSpLinkPlanCapacityRcvd cItpSpLinkUtilThresholdRcvd cItpSpLinkUtilizationRcvd cItpSpLinkUtilStateRcvd cItpSpLinkL2BytesRcvd cItpSpLinkPlanCapacitySent cItpSpLinkUtilThresholdSent cItpSpLinkUtilizationSent cItpSpLinkUtilStateSent cItpSpLinkL2BytesSent Notification enable: cItpSpLinkUtilNotifEnabled Notification: cItpSpLinkRcvdUtilChange cItpSpLinkSentUtilChange" REVISION "200201230000Z" DESCRIPTION "Modified the following objects: cItpSpLinkType: Added new high speed link type to textual convention CItpTcLinkType. cItpSpVariant: Added new China SS7 variant to textual convention CItpTcSs7Variant. Add new enumerate Added the following objects: cItpSpDistSccpUnseq cItpSpSummaryRoutingException cItpSpLinksetVariant cItpSpLinkDroppedPkts cItpSpLinkTransmittedLssu cItpSpLinkReceivedLssu cItpSpLinkProtocolDetails cItpSpLinkLsacState cItpSpLinkTsrcState cItpSpLinkTcocState cItpSpLinkTcocLocalBSNT cItpSpLinkTcocRemoteBSNT cItpSpLinkTcbcState cItpSpLinkReceivedSIB cItpSpLinkTransmittedSIB cItpSpLinkMtp2ExpiredT01 cItpSpLinkMtp2ExpiredT02 cItpSpLinkMtp2ExpiredT03 cItpSpLinkMtp2ExpiredT04 cItpSpLinkMtp2ExpiredT05 cItpSpLinkMtp2ExpiredT06 cItpSpLinkMtp2ExpiredT07 cItpSpLinkOMAERMCount cItpSpLinkOMAERMFailCount cItpSpLinkOMSURMCount cItpSpLinkOMSURMFailCount" REVISION "200108290000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 232 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.232.0 | cItpSpMIBNotifs | 1 | 6 | None |
| 1.3.6.1.4.1.9.9.232.1 | cItpSpMIBObjects | 5 | 358 | None |
| 1.3.6.1.4.1.9.9.232.2 | cItpSpMIBConformance | 2 | 17 | None |
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.9.9.183 | ciscoGprsAccPtMIB | 3 | 338 | This MIB module supports access point configuration for GGSN in a GPRS system. GPRS [1] is a GSM network providing mobile wireles… |
| 1.3.6.1.4.1.9.9.184 | ciscoPimMIB | 3 | 36 | This MIB module defines the cisco specific variables for Protocol Independent Multicast (PIM) management. These definitions are a… |
| 1.3.6.1.4.1.9.9.185 | ciscoBertMIB | 2 | 46 | The MIB module to configure and perform Bit Error Rate Testing (BERT) on DS3, DS1/E1 and DS0/DS0Bundle interfaces. Bit error rate… |
| 1.3.6.1.4.1.9.9.187 | ciscoBgp4MIB | 4 | 137 | An extension to the IETF BGP4 MIB module defined in RFC 1657. Following is the terminology associated with Border Gateway Protocol… |
| 1.3.6.1.4.1.9.9.188 | cGtpMIB | 3 | 248 | This MIB module manages the GPRS Tunnelling Protocol (GTP) on GGSN and SGSN. GPRS provides wireless access to packet data network… |
| 1.3.6.1.4.1.9.9.189 | ciscoPortQosMIB | 3 | 114 | Cisco PORT QOS MIB - Overview This MIB module is for the management of Cisco's per port rate-limiting and traffic shaping on L3 sw… |
| 1.3.6.1.4.1.9.9.190 | ciscoVoiceAppsMIB | 3 | 40 | The MIB Module for the management of Cisco Voice Applications. This MIB is designed to work in conjunction with the SYSAPPL-MIB … |
| 1.3.6.1.4.1.9.9.191 | ciscoIpUplinkRedirectMIB | 3 | 11 | This MIB module is for the configuration of Cisco IP Uplink Redirect feature. |
| 1.3.6.1.4.1.9.9.192 | ciscoGprsChargingMIB | 3 | 315 | This MIB module manages the charging related function on the GGSN node of a GPRS system. The following diagram illustrates a simp… |
| 1.3.6.1.4.1.9.9.194 | ciscoPppoeMIB | 3 | 89 | Cisco PPPoE sessions management MIB Module. |
| 1.3.6.1.4.1.9.9.195 | ciscoEntityExtMIB | 3 | 64 | This MIB is an extension of the ENTITY-MIB specified in RFC2737. This MIB module contains Cisco-defined extensions to the entit… |
| 1.3.6.1.4.1.9.9.197 | ciscoDistDirMIB | 3 | 123 | Cisco Distributed Director MIB. The Cisco Distributed Director provides global Internet scalability and increased performance as … |
| 1.3.6.1.4.1.9.9.198 | ciscoRfSupMIB | 3 | 58 | This MIB was designed to complement the CISCO-RF-MIB by providing additional optional status and configuration control for redund… |
| 1.3.6.1.4.1.9.9.199 | ciscoSmFileDownloadMIB | 3 | 23 | The MIB module for downloading files to the Service Modules specifically designed for an architecture containing a controller car… |
| 1.3.6.1.4.1.9.9.201 | ciscoSwitchUsageMIB | 3 | 15 | This MIB defines objects related to statistics for the usage of switch fabric. The switch fabric is used by the incoming packets … |
| 1.3.6.1.4.1.9.9.202 | ciscoOscpMIB | 3 | 52 | The MIB module for managing the Cisco Optical Supervisory Channel Protocol (OSCP). The OSCP is used to determine and maintain wav… |
| 1.3.6.1.4.1.9.9.204 | ciscoXdslLineMIB | 2 | 32 | The tables defined by this MIB module contain a collection of managed objects that are general in nature and apply to different t… |
| 1.3.6.1.4.1.9.9.215 | ciscoMacNotificationMIB | 3 | 72 | This MIB module is for configuration of the MAC notification feature. MAC notification is a mechanism to inform monitoring device… |
| 1.3.6.1.4.1.9.9.216 | ciscoContentNetworkMIB | 3 | 34 | This MIB module defines objects for Content Network devices. A Content Network is a collection of devices that optimizes the deli… |
| 1.3.6.1.4.1.9.9.217 | ciscoCat6kCrossbarMIB | 3 | 210 | The Catalyst 6000 Crossbar MIB provides instrumentation for configuration and operation of the crossbar switching fabric module, … |
| 1.3.6.1.4.1.9.9.218 | ciscoIfThresholdMIB | 3 | 65 | ciscoIfthresholdMIB |
| 1.3.6.1.4.1.9.9.219 | ciscoVoiceDnisMIB | 3 | 24 | The MIB module provides management support for Dialer Number Information Service (DNIS) mapping. A DNIS entry is associated with… |
| 1.3.6.1.4.1.9.9.220 | ciscoPaeMIB | 3 | 231 | Cisco Port Access Entity (PAE) module for managing IEEE Std 802.1x. This MIB provides Port Access Entity information that are eith… |
| 1.3.6.1.4.1.9.9.221 | ciscoEnhancedMemPoolMIB | 3 | 87 | New MIB module for monitoring the memory pools of all physical entities on a managed system. |
| 1.3.6.1.4.1.9.9.222 | ciscoEnhancedWredMIB | 3 | 70 | Cisco WRED MIB - Overview Cisco Weighted Random Early Detection/Drop (WRED) is a method which avoids traffic congestion on an outp… |
| 1.3.6.1.4.1.9.9.223 | ciscoWanNcdpMIB | 3 | 58 | This MIB module is intended for the management of network clock distribution and the Network Clock Distribution Protocol (NCDP) i… |
| 1.3.6.1.4.1.9.9.224 | ciscoDevExcepReportMIB | 3 | 29 | This mib defines the SNMP objects to report exceptions to north-bound NMS. The devices implementing this MIB monitor the status of… |
| 1.3.6.1.4.1.9.9.225 | ciscoLagMIB | 3 | 56 | Cisco Link Aggregation module for managing IEEE Std 802.3ad. This MIB provides Link Aggregation information that are either exclud… |
| 1.3.6.1.4.1.9.9.226 | ciscoNDEMIB | 4 | 17 | The Netflow Data Export (NDE) MIB provides instrumentation for configuration and operation of the Netflow Data Export feature. A … |
| 1.3.6.1.4.1.9.9.227 | ciscoItpAclMIB | 3 | 45 | The MIB for managing access lists that control messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Trans… |
| 1.3.6.1.4.1.9.9.228 | ciscoItpRtMIB | 3 | 47 | This MIB is for managing information required to route messages transported over Signalling System No. 7 (SS7) Network via Cisco … |
| 1.3.6.1.4.1.9.9.229 | ciscoDs1ExtMIB | 2 | 129 | The MIB module to describe DS1/E1 interface objects. This is an extension to the standard DS1/E1 MIB (RFC 2495). Unless mentioned… |
| 1.3.6.1.4.1.9.9.230 | ciscoItpActMIB | 3 | 29 | The MIB for providing information specified in ITU Q752 Monitoring and Measurements for Signalling System No. 7(SS7) Network. This… |
| 1.3.6.1.4.1.9.9.231 | ciscoItpTextualConventions | 0 | 0 | The defines textual conventions used by to manage devices related to the SS7 network. The relevant ITU documents describing this… |
| 1.3.6.1.4.1.9.9.233 | ciscoItpSccpMIB | 3 | 194 | The MIB for Signaling Connection Control Part(SCCP) messages transported over Signalling System No. 7 (SS7) Network via Cisco IP … |
| 1.3.6.1.4.1.9.9.234 | ciscoWanTopologyMIB | 3 | 83 | A management station can use this MIB module for the maintenance of persistent topology information of the PNNI network. Previous… |
| 1.3.6.1.4.1.9.9.235 | ciscoImaMIB | 2 | 60 | The MIB module describes Cisco IMA objects. This is an extension to the standard of ATM Forum IMA version 1.1, AF-PHY-0086.001 Spe… |
| 1.3.6.1.4.1.9.9.236 | ciscoWanSctMgmtMIB | 2 | 18 | MIB module to manage SCT files in a node. SCTs (Service Class Templates) are nodal configuration files, which define the traffic … |
| 1.3.6.1.4.1.9.9.237 | ciscoNmsApplHealthMIB | 3 | 21 | This MIB defines Cisco NMS Application (cna) Health Status Notifications and the related objects. These notifications will be sen… |
| 1.3.6.1.4.1.9.9.238 | ciscoIGMPFilterMIB | 2 | 45 | IGMP Filter configuration MIB. This MIB provides a mechanism for users to configure the system to intercept IGMP joins for IP Mul… |
| 1.3.6.1.4.1.9.9.240 | cGgsnMIB | 3 | 389 | This MIB module manages the Gateway GPRS Support Node (GGSN) devices. A GGSN device provides interworking with external packet-dat… |
| 1.3.6.1.4.1.9.9.241 | cggsnQosMIB | 2 | 89 | This MIB module manages the Quality of Service parameters of GGSN in a GPRS system. GGSN is the Gateway GPRS Support Node in the … |
| 1.3.6.1.4.1.9.9.242 | ciscoCableAvailabilityMIB | 3 | 60 | This is the MIB module for management of Hot Standby Connection to Connection Protocol (HCCP) features. HCCP is a Cisco proprieta… |
| 1.3.6.1.4.1.9.9.243 | ciscoHealthMonitorMIB | 3 | 22 | Health Monitor MIB module. The Health Monitor uses a model based on events of varying severity and frequency, and predefined rule… |
| 1.3.6.1.4.1.9.9.244 | ciscoNbarProtocolDiscoveryMIB | 3 | 84 | Cisco NBAR Protocol Discovery MIB NBAR - Network Based Application Recognition is an intelligent classification engine that reco… |
| 1.3.6.1.4.1.9.9.245 | ciscoGtpDirectorMIB | 3 | 35 | This MIB module defines objects that are used to manage GTP Director Module. In the GPRS network, the APN is the identifier that s… |
| 1.3.6.1.4.1.9.9.246 | ciscoL2TunnelConfigMIB | 3 | 65 | This MIB module is for layer 2 tunneling related configurations on a device. Tunneling allows separate local networks to be consi… |
| 1.3.6.1.4.1.9.9.248 | ciscoItpSp2MIB | 3 | 30 | The MIB for providing information specified in ITU Q752 Monitoring and Measurements for Signaling System No. 7(SS7) Network. This … |
| 1.3.6.1.4.1.9.9.249 | ciscoEnhancedImageMIB | 2 | 44 | Initial version of the MIB. This MIB has Image table containing the following information related to the running IOS image 1. Enti… |
| 1.3.6.1.4.1.9.9.252 | cTapMIB | 3 | 80 | This module manages Cisco's intercept feature. |
| 1.3.6.1.4.1.9.9.253 | ciscoItpXuaMIB | 3 | 250 | The MIB for MTP3 User Adaptation (M3UA) and SCCP User Adaptation (SUA) for Cisco's IP Transfer Point (ITP) implementation. The Cis… |
| 1.3.6.1.4.1.9.9.254 | ciscoSlbExtMIB | 3 | 425 | The extended MIB for managing Server Load Balancing Manager(s). This MIB extends the SLB management functionality in the CISCO-SL… |
| 1.3.6.1.4.1.9.9.255 | ciscoFabricMcastMIB | 3 | 30 | Fabric Multicast Resource MIB module. This MIB module is used for managing/tracking the fabric multicast resource related informa… |
| 1.3.6.1.4.1.9.9.256 | ciscoFabricMcastApplMIB | 3 | 16 | Fabric multicast resource MIB module. This MIB module is used for managing/tracking the fabric multicast resource application rel… |
| 1.3.6.1.4.1.9.9.257 | ciscoFabricHfrMIB | 3 | 90 | Cisco Enhanced Benes fabric MIB module. This MIB module is used for managing/tracking the Ehanced Benes Fabric entities and/or fa… |
| 1.3.6.1.4.1.9.9.259 | ciscoPsaMicrocodeMIB | 3 | 24 | Cisco PSA Microcode MIB - Overview The PSA is the Packet Switching ASIC used in module like engine 2(E2) line cards in GSR for IP … |
| 1.3.6.1.4.1.9.9.260 | ciscoSsgMIB | 3 | 218 | The MIB Module manages Service Selection Gateway(SSG) devices. Service Selection Gateway(SSG) is a switching solution for service… |
| 1.3.6.1.4.1.9.9.261 | ciscoPtopoExtnMIB | 2 | 18 | This MIB module contains extensions to the PTOPO-MIB that provide support to distinguish between bidirectional and unidirectional… |
| 1.3.6.1.4.1.9.9.262 | ciscoVoaMIB | 2 | 14 | This MIB module defines objects to configure and manage the Variable Optical Attenuator (VOA) modules. VOA modules are typically … |
| 1.3.6.1.4.1.9.9.263 | ciscoIgmpSnoopingMIB | 3 | 286 | The MIB module for IGMP Snooping feature. Internet Group Management Protocol (IGMP) is the protocol used by IPv4 end hosts to ind… |
| 1.3.6.1.4.1.9.9.264 | ciscoOpticalMonitorMIB | 3 | 72 | This MIB module defines objects to monitor optical characteristics and set corresponding thresholds on the optical interfaces in … |
| 1.3.6.1.4.1.9.9.265 | ciscoEntityPfeMib | 3 | 58 | The Packet Forwarding Engine technology are Cisco developed Network Processors, which accelerates certain features in order to pr… |
| 1.3.6.1.4.1.9.9.268 | ciscoWlanVlanMIB | 3 | 41 | This MIB module provides network management support for device VLAN configuration on IEEE 802.11 wireless LAN. ACRONYMS AES Advanced… |
| 1.3.6.1.4.1.9.9.269 | ciscoTBridgeDevIfMIB | 2 | 20 | This MIB module provides network management support for configuration and status information of devices supporting transparent br… |
| 1.3.6.1.4.1.9.9.270 | ciscoSyslogEventExtMIB | 2 | 21 | This MIB module extends the Cisco Syslog MIB and provides network management support to handle and process Syslog messages as devi… |
| 1.3.6.1.4.1.9.9.271 | ciscoL2DevMonMIB | 3 | 24 | This MIB module is for monitoring of active layer 2 devices by hot standby layer 2 devices and the configuration of hot standby s… |
| 1.3.6.1.4.1.9.9.272 | ciscoDot11IfMIB | 3 | 212 | This MIB module provides network management support for Cisco IEEE 802.11 Wireless LAN type device (Access Point) radio interface… |
| 1.3.6.1.4.1.9.9.273 | ciscoDot11AssociationMIB | 2 | 91 | This MIB module provides network management information on IEEE 802.11 wireless device association management and data packet for… |
| 1.3.6.1.4.1.9.9.275 | ciscoBcpMIB | 2 | 25 | This MIB module describes the Managed Objects for of Bridge Control Protocol (RFC2878). This MIB is influenced by RFC1474. |
| 1.3.6.1.4.1.9.9.276 | ciscoIfExtensionMIB | 3 | 143 | A MIB module for extending the IF-MIB (RFC2863) to add objects which provide additional information about interfaces not availabl… |
| 1.3.6.1.4.1.9.9.277 | ciscoDdpIappMIB | 3 | 22 | This MIB module describes the management support for the Inter-Access Point Protocol (IAPP). IAPP is a Cisco propriety Data Deli… |
| 1.3.6.1.4.1.9.9.278 | ciscoIpProtocolMIB | 3 | 63 | The MIB module is for management of information to support packet filtering on IP protocols. The cippfIpProfileTable allows users… |
| 1.3.6.1.4.1.9.9.279 | ciscoAtmQosMIB | 3 | 67 | The MIB is created to provide ATM QoS information in these areas: 1. Traffic shaping on a per-VC basis 2. Traffic shaping on a pe… |
| 1.3.6.1.4.1.9.9.280 | ciscoOutageMIB | 3 | 75 | This MIB module describes, stores, and reports outage related information generated by individual hardware and software component… |
| 1.3.6.1.4.1.9.9.281 | ciscoFabricC12kMIB | 3 | 135 | Cisco Fabric MIB module for c12000 series of routers. This MIB module is used for managing/tracking the c12000 fabric entities an… |
| 1.3.6.1.4.1.9.9.282 | ciscoVsanMIB | 2 | 104 | The MIB module for the management of the Virtual Storage Networks (VSANs) within the frame work of Cisco's VSAN Architecture. T… |
| ... | ||||