{1 3 6 1 4 1 4491 2 1 30 1 2 8 1 22}
This attribute reports options implemented in the transceiver. Note: The encoding of bit values of this attribute reflects the inverse bit numbering convention of the SFF specification.
This attribute reports options implemented in the transceiver.
This attribute reports options implemented in the transceiver as described in the Options Values table of [SFF 8472]. The following rate identifier types can be reported: unallocated: unallocated options value rxlosNormal: Loss of Signal implemented, behavior as defined in [SFF 8419] (often called Rx_LOS) rxlosInverted: Loss of Signal implemented, signal inverted from standard definition in SFP MSA (often called Signal Detect) txFault: TX_FAULT signal implemented. Reference [SFF 8419] txDisable: TX_DISABLE is implemented and disables the high speed serial output. rateSelect: RATE_SELECT functionality is implemented. unallocated6: unallocated options value unallocated7: unallocated options value powerLevel: Power Level Declaration. Value of zero identifies Power Level 1 (or unspecified) requirements. Value of one identifies Power Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and Status Functions table and Extended Module Control/Status Bytes table for control, status, timing. See [SFF 8472] Option Values table Address A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration. Reference [SFF 8431]. cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies a conventional uncooled (or unspecified) laser implementation. Value of one identifies a cooled laser transmitter implementation. Reference [SFF 8431]. Reference [SFF 8472]
Status in source: current.
Names: docsRphyRpdIfEnetSfpPlusStatusOptions
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"docsRphyRpdIfEnetSfpPlusStatusOptions",
"OBJECT-TYPE",
"SYNTAX",
"BITS",
"{",
"reserved0",
"(",
"0",
")",
",",
"reserved1",
"(",
"1",
")",
",",
"reserved2",
"(",
"2",
")",
",",
"reserved3",
"(",
"3",
")",
",",
"reserved4",
"(",
"4",
")",
",",
"cooledTransceiver",
"(",
"5",
")",
",",
"powerLevel",
"(",
"6",
")",
",",
"linearOutput",
"(",
"7",
")",
",",
"unallocated7",
"(",
"8",
")",
",",
"unallocated6",
"(",
"9",
")",
",",
"rateSelect",
"(",
"10",
")",
",",
"txDisable",
"(",
"11",
")",
",",
"txFault",
"(",
"12",
")",
",",
"rxlosInverted",
"(",
"13",
")",
",",
"rxlosNormal",
"(",
"14",
")",
",",
"unallocated0",
"(",
"15",
")",
"}",
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"This attribute reports options implemented in the transceiver. Note: The encoding of bit values of this attribute reflects the inverse bit numbering convention of the SFF specification.\"",
"::=",
"{",
"docsRphyRpdIfEnetSfpPlusStatusEntry",
"22",
"}"
],
"syntax_tree": [
[
"BITS",
[
[
"reserved0",
0
],
[
"reserved1",
1
],
[
"reserved2",
2
],
[
"reserved3",
3
],
[
"reserved4",
4
],
[
"cooledTransceiver",
5
],
[
"powerLevel",
6
],
[
"linearOutput",
7
],
[
"unallocated7",
8
],
[
"unallocated6",
9
],
[
"rateSelect",
10
],
[
"txDisable",
11
],
[
"txFault",
12
],
[
"rxlosInverted",
13
],
[
"rxlosNormal",
14
],
[
"unallocated0",
15
]
]
],
null,
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"This attribute reports options implemented in the transceiver. Note: The encoding of bit values of this attribute reflects the inverse bit numbering convention of the SFF specification."
],
null,
null,
null,
null
]
}Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
reserved0(0),
reserved1(1),
reserved2(2),
reserved3(3),
reserved4(4),
cooledTransceiver(5),
powerLevel(6),
linearOutput(7),
unallocated7(8),
unallocated6(9),
rateSelect(10),
txDisable(11),
txFault(12),
rxlosInverted(13),
rxlosNormal(14),
unallocated0(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the
transceiver. Note: The encoding of bit values of this
attribute reflects the inverse bit numbering
convention of the SFF specification."
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:56.205690+00:00.
Status in source: current.
Names: docsRphyRpdIfEnetSfpPlusStatusOptions
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"docsRphyRpdIfEnetSfpPlusStatusOptions",
"OBJECT-TYPE",
"SYNTAX",
"BITS",
"{",
"unallocated0",
"(",
"0",
")",
",",
"rxlosNormal",
"(",
"1",
")",
",",
"rxlosInverted",
"(",
"2",
")",
",",
"txFault",
"(",
"3",
")",
",",
"txDisable",
"(",
"4",
")",
",",
"rateSelect",
"(",
"5",
")",
",",
"unallocated6",
"(",
"6",
")",
",",
"unallocated7",
"(",
"7",
")",
",",
"linearOutput",
"(",
"8",
")",
",",
"powerLevel",
"(",
"9",
")",
",",
"cooledTransceiver",
"(",
"10",
")",
"}",
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"This attribute reports options implemented in the transceiver.\"",
"::=",
"{",
"docsRphyRpdIfEnetSfpPlusStatusEntry",
"22",
"}"
],
"syntax_tree": [
[
"BITS",
[
[
"unallocated0",
0
],
[
"rxlosNormal",
1
],
[
"rxlosInverted",
2
],
[
"txFault",
3
],
[
"txDisable",
4
],
[
"rateSelect",
5
],
[
"unallocated6",
6
],
[
"unallocated7",
7
],
[
"linearOutput",
8
],
[
"powerLevel",
9
],
[
"cooledTransceiver",
10
]
]
],
null,
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"This attribute reports options implemented in the transceiver."
],
null,
null,
null,
null
]
}Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver."
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex', 'InterfaceIndexOrZero'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'AutonomousType', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'DOCS-IETF-BPI2-MIB': ['DocsX509ASN1DEREncodedCertificate'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:55.074775+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver."
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:55.180890+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver."
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:55.289076+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver."
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:55.938082+00:00.
Status in source: current.
Names: docsRphyRpdIfEnetSfpPlusStatusOptions
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"docsRphyRpdIfEnetSfpPlusStatusOptions",
"OBJECT-TYPE",
"SYNTAX",
"BITS",
"{",
"unallocated0",
"(",
"0",
")",
",",
"rxlosNormal",
"(",
"1",
")",
",",
"rxlosInverted",
"(",
"2",
")",
",",
"txFault",
"(",
"3",
")",
",",
"txDisable",
"(",
"4",
")",
",",
"rateSelect",
"(",
"5",
")",
",",
"unallocated6",
"(",
"6",
")",
",",
"unallocated7",
"(",
"7",
")",
",",
"linearOutput",
"(",
"8",
")",
",",
"powerLevel",
"(",
"9",
")",
",",
"cooledTransceiver",
"(",
"10",
")",
",",
"reserved11",
"(",
"11",
")",
",",
"reserved12",
"(",
"12",
")",
",",
"reserved13",
"(",
"13",
")",
",",
"reserved14",
"(",
"14",
")",
",",
"reserved15",
"(",
"15",
")",
"}",
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"This attribute reports options implemented in the transceiver.\"",
"::=",
"{",
"docsRphyRpdIfEnetSfpPlusStatusEntry",
"22",
"}"
],
"syntax_tree": [
[
"BITS",
[
[
"unallocated0",
0
],
[
"rxlosNormal",
1
],
[
"rxlosInverted",
2
],
[
"txFault",
3
],
[
"txDisable",
4
],
[
"rateSelect",
5
],
[
"unallocated6",
6
],
[
"unallocated7",
7
],
[
"linearOutput",
8
],
[
"powerLevel",
9
],
[
"cooledTransceiver",
10
],
[
"reserved11",
11
],
[
"reserved12",
12
],
[
"reserved13",
13
],
[
"reserved14",
14
],
[
"reserved15",
15
]
]
],
null,
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"This attribute reports options implemented in the transceiver."
],
null,
null,
null,
null
]
}Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the
transceiver."
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:56.354948+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the
transceiver."
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:56.429401+00:00.
Status in source: current.
Names: docsRphyRpdIfEnetSfpPlusStatusOptions
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"docsRphyRpdIfEnetSfpPlusStatusOptions",
"OBJECT-TYPE",
"SYNTAX",
"BITS",
"{",
"unallocated0",
"(",
"0",
")",
",",
"rxlosNormal",
"(",
"1",
")",
",",
"rxlosInverted",
"(",
"2",
")",
",",
"txFault",
"(",
"3",
")",
",",
"txDisable",
"(",
"4",
")",
",",
"rateSelect",
"(",
"5",
")",
",",
"unallocated6",
"(",
"6",
")",
",",
"unallocated7",
"(",
"7",
")",
",",
"linearOutput",
"(",
"8",
")",
",",
"powerLevel",
"(",
"9",
")",
",",
"cooledTransceiver",
"(",
"10",
")",
",",
"reserved11",
"(",
"11",
")",
",",
"reserved12",
"(",
"12",
")",
",",
"reserved13",
"(",
"13",
")",
",",
"reserved14",
"(",
"14",
")",
",",
"reserved15",
"(",
"15",
")",
"}",
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"This attribute reports options implemented in the transceiver as described in the Options Values table of [SFF 8472]. The following rate identifier types can be reported: unallocated: unallocated options value rxlosNormal: Loss of Signal implemented, behavior as defined in [SFF 8419] (often called Rx_LOS) rxlosInverted: Loss of Signal implemented, signal inverted from standard definition in SFP MSA (often called Signal Detect) txFault: TX_FAULT signal implemented. Reference [SFF 8419] txDisable: TX_DISABLE is implemented and disables the high speed serial output. rateSelect: RATE_SELECT functionality is implemented. unallocated6: unallocated options value unallocated7: unallocated options value powerLevel: Power Level Declaration. Value of zero identifies Power Level 1 (or unspecified) requirements. Value of one identifies Power Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and Status Functions table and Extended Module Control/Status Bytes table for control, status, timing. See [SFF 8472] Option Values table Address A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration. Reference [SFF 8431]. cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies a conventional uncooled (or unspecified) laser implementation. Value of one identifies a cooled laser transmitter implementation. Reference [SFF 8431]. Reference [SFF 8472]\"",
"::=",
"{",
"docsRphyRpdIfEnetSfpPlusStatusEntry",
"22",
"}"
],
"syntax_tree": [
[
"BITS",
[
[
"unallocated0",
0
],
[
"rxlosNormal",
1
],
[
"rxlosInverted",
2
],
[
"txFault",
3
],
[
"txDisable",
4
],
[
"rateSelect",
5
],
[
"unallocated6",
6
],
[
"unallocated7",
7
],
[
"linearOutput",
8
],
[
"powerLevel",
9
],
[
"cooledTransceiver",
10
],
[
"reserved11",
11
],
[
"reserved12",
12
],
[
"reserved13",
13
],
[
"reserved14",
14
],
[
"reserved15",
15
]
]
],
null,
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"This attribute reports options implemented in the transceiver as described in the Options Values table of [SFF 8472]. The following rate identifier types can be reported: unallocated: unallocated options value rxlosNormal: Loss of Signal implemented, behavior as defined in [SFF 8419] (often called Rx_LOS) rxlosInverted: Loss of Signal implemented, signal inverted from standard definition in SFP MSA (often called Signal Detect) txFault: TX_FAULT signal implemented. Reference [SFF 8419] txDisable: TX_DISABLE is implemented and disables the high speed serial output. rateSelect: RATE_SELECT functionality is implemented. unallocated6: unallocated options value unallocated7: unallocated options value powerLevel: Power Level Declaration. Value of zero identifies Power Level 1 (or unspecified) requirements. Value of one identifies Power Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and Status Functions table and Extended Module Control/Status Bytes table for control, status, timing. See [SFF 8472] Option Values table Address A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration. Reference [SFF 8431]. cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies a conventional uncooled (or unspecified) laser implementation. Value of one identifies a cooled laser transmitter implementation. Reference [SFF 8431]. Reference [SFF 8472]"
],
null,
null,
null,
null
]
}Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:57.003028+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:57.394938+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:57.424309+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:57.542970+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:58.089920+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'DOCS-IF-MIB': ['InterfaceIndex', 'TenthdB', 'TenthdBmV'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Source data warning: Recovered from a file whose complete MIB does not parse. The original assignment and definition are preserved. Registration and implementation details may be inaccurate; consult the original file. Other damaged or unresolved declarations are not established registrations.
· Download DOCS-RPHY-MIB-2023-10-12.txtDownloaded: 2026-10-26T22:49:58.579257+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'DOCS-IF-MIB': ['TenthdB', 'TenthdBmV'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:58.575041+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'DOCS-IF-MIB': ['TenthdB', 'TenthdBmV'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:49:58.705674+00:00.
Module: DOCS-RPHY-MIB
docsRphyRpdIfEnetSfpPlusStatusOptions OBJECT-TYPE
SYNTAX BITS {
unallocated0(0),
rxlosNormal(1),
rxlosInverted(2),
txFault(3),
txDisable(4),
rateSelect(5),
unallocated6(6),
unallocated7(7),
linearOutput(8),
powerLevel(9),
cooledTransceiver(10),
reserved11(11),
reserved12(12),
reserved13(13),
reserved14(14),
reserved15(15)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This attribute reports options implemented in the transceiver
as described in the Options Values table of [SFF 8472].
The following rate identifier types can be reported:
unallocated: unallocated options value
rxlosNormal: Loss of Signal implemented, behavior as defined in
[SFF 8419] (often called Rx_LOS)
rxlosInverted: Loss of Signal implemented, signal inverted from
standard definition in SFP MSA (often called Signal Detect)
txFault: TX_FAULT signal implemented. Reference [SFF 8419]
txDisable: TX_DISABLE is implemented and disables the high speed serial output.
rateSelect: RATE_SELECT functionality is implemented.
unallocated6: unallocated options value
unallocated7: unallocated options value
powerLevel: Power Level Declaration. Value of zero identifies Power
Level 1 (or unspecified) requirements. Value of one identifies Power
Level 2 requirement. See [SFF 8472] I/O Timing for Soft Control and
Status Functions table and Extended Module Control/Status Bytes table
for control, status, timing. See [SFF 8472] Option Values table Address
A0h byte 64, Bit 5 for Power Level 3 declaration. See [SFF 8472] Option
Values table Address A0h byte 64, Bit 6 for Power Level 4 declaration.
Reference [SFF 8431].
cooledTransceiver: Cooled Transceiver Declaration. Value of zero identifies
a conventional uncooled (or unspecified) laser implementation. Value of one
identifies a cooled laser transmitter implementation. Reference [SFF 8431].
Reference [SFF 8472]"
::= { docsRphyRpdIfEnetSfpPlusStatusEntry 22 }{'IF-MIB': ['InterfaceIndex', 'ifIndex'], 'IP-MIB': ['IpAddressOriginTC', 'IpAddressStatusTC', 'Ipv6AddressIfIdentifierTC'], 'SNMPv2-TC': ['TruthValue', 'MacAddress', 'TimeStamp', 'DateAndTime', 'PhysAddress', 'TEXTUAL-CONVENTION'], 'ENTITY-MIB': ['PhysicalIndex', 'PhysicalIndexOrZero'], 'SNMPv2-SMI': ['MODULE-IDENTITY', 'OBJECT-TYPE', 'Unsigned32', 'Gauge32', 'Counter32', 'Counter64', 'Integer32'], 'DOCS-IF-MIB': ['TenthdB', 'TenthdBmV'], 'SNMPv2-CONF': ['OBJECT-GROUP', 'MODULE-COMPLIANCE'], 'UUID-TC-MIB': ['UUIDorZero'], 'CLAB-DEF-MIB': ['clabProjDocsis'], 'DOCS-IF3-MIB': ['IfDirection', 'docsIf3CmtsCmRegStatusId'], 'IANAifType-MIB': ['IANAifType'], 'IANA-ENTITY-MIB': ['IANAPhysicalClass'], 'INET-ADDRESS-MIB': ['InetAddressType', 'InetAddress', 'InetPortNumber', 'InetVersion', 'InetAddressPrefixLength'], 'ENTITY-SENSOR-MIB': ['EntitySensorDataType', 'EntitySensorDataScale', 'EntitySensorPrecision', 'EntitySensorValue', 'EntitySensorStatus'], 'SNMP-FRAMEWORK-MIB': ['SnmpAdminString']}Downloaded: 2026-10-26T22:47:25.372984+00:00.
| OID | Name | Direct children | Descendants | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.1 | docsRphyRpdIfEnetSfpPlusStatusStatus | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.2 | docsRphyRpdIfEnetSfpPlusStatusIdentifier | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.3 | docsRphyRpdIfEnetSfpPlusStatusExtendedIdentifier | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.4 | docsRphyRpdIfEnetSfpPlusStatusConnectorType | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.5 | docsRphyRpdIfEnetSfpPlusStatusTransceiverComplianceCodes | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.6 | docsRphyRpdIfEnetSfpPlusStatusTransceiverComplianceCode36 | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.7 | docsRphyRpdIfEnetSfpPlusStatusEncoding | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.8 | docsRphyRpdIfEnetSfpPlusStatusBitRateNominal | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.9 | docsRphyRpdIfEnetSfpPlusStatusRateIdentifier | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.10 | docsRphyRpdIfEnetSfpPlusStatusLengthKm | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.11 | docsRphyRpdIfEnetSfpPlusStatusLength100M | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.12 | docsRphyRpdIfEnetSfpPlusStatusLength50Mi10M | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.13 | docsRphyRpdIfEnetSfpPlusStatusLength62Pt5Mi10M | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.14 | docsRphyRpdIfEnetSfpPlusStatusLengthCopperM | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.15 | docsRphyRpdIfEnetSfpPlusStatusLength50MiOm3 | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.16 | docsRphyRpdIfEnetSfpPlusStatusVendorName | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.17 | docsRphyRpdIfEnetSfpPlusStatusVendorOui | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.18 | docsRphyRpdIfEnetSfpPlusStatusVendorPartNum | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.19 | docsRphyRpdIfEnetSfpPlusStatusVendorSerialNum | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.20 | docsRphyRpdIfEnetSfpPlusStatusVendorRev | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.21 | docsRphyRpdIfEnetSfpPlusStatusLaserWavelength | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.23 | docsRphyRpdIfEnetSfpPlusStatusBitRateMax | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.24 | docsRphyRpdIfEnetSfpPlusStatusBitRateMin | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.25 | docsRphyRpdIfEnetSfpPlusStatusVendorDate | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.26 | docsRphyRpdIfEnetSfpPlusStatusVendorSpecificLotCode | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.27 | docsRphyRpdIfEnetSfpPlusStatusDiagMonitorType | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.28 | docsRphyRpdIfEnetSfpPlusStatusEnhancedOptions | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.29 | docsRphyRpdIfEnetSfpPlusStatusSff8472Compliance | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.30 | docsRphyRpdIfEnetSfpPlusStatusVendorSpecificData | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.31 | docsRphyRpdIfEnetSfpPlusStatusMeasuredTxOutputPwr | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.32 | docsRphyRpdIfEnetSfpPlusStatusMeasuredRxInputPwr | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.33 | docsRphyRpdIfEnetSfpPlusStatusDigitalDiagA2Info | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.34 | docsRphyRpdIfEnetSfpPlusStatusMeasuredTxBiasCurrent | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.35 | docsRphyRpdIfEnetSfpPlusStatusMeasuredTemperature | 0 | 0 | |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.36 | docsRphyRpdIfEnetSfpPlusStatusMeasuredSupplyVoltage | 0 | 0 |