Available source records contain 8 distinct definitions; some records may not include a definition.
Show 8 published definitions
eventConfigMode · mandatory
eventConfigMode OBJECT-TYPE
SYNTAX INTEGER { other (1),
onChange (2),
greaterThanValue (3),
smallerThanValue (4),
hysteresisBound (5),
periodic (6),
andedWithValue (7) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"<Definition>This object specifies the mode of operation for
this event. The modes are defined as follows:
Value Description
other the event mode of operation is not
described in this standard, refer to the
device manual.
onChange create a log entry when the object value
referenced by eventConfigCompareOID
changes. The values of
eventConfigCompareValue and
eventConfigCompareValue2 are ignored in
this mode.
greaterThanValue create a log entry when the object value
referenced by eventConfigCompareOID
becomes greater than the value of
eventConfigCompareValue for the time
(tenth seconds) defined by
eventConfigCompareValue2 (zero means
immediate logging).
smallerThanValue create a log entry when the object value
referenced by eventConfigCompareOID
becomes less than the value of
eventConfigCompareValue for the time
(tenth seconds) defined by
eventConfigCompareValue2 (zero means
immediate logging).
hysteresisBound create a log entry when the object value
referenced by eventConfigCompareOID
becomes less than or greater than the
bound values. The lowerbound value is the
lower value of eventConfigCompareValue and
eventConfigCompareValue2; the upperbound
value is the higher value of the two values.
When the object value becomes greater than
the upper bound value, subsequent logging of
upperbound conditions shall not occur until
the object value becomes less than the
lower bound value.
When the object value becomes less than
the lower bound value, subsequent logging
of lowerbound conditions shall not occur
until the object value becomes greater
than the upper bound value.
periodic create a log entry every x seconds, where
x is defined by the value stored in
eventConfigCompareValue. The values stored
in eventConfigCompareValue2 and
eventConfigCompareOID are ignored in this
mode.
andedWithValue create a log entry when the object value
referenced by eventConfigCompareOID ANDED
with the value of eventConfigCompareValue
is NOT equal to zero for the time (tenth
seconds) defined by eventConfigCompareValue2
(zero means immediate logging). This allows
monitoring of a specific bit; the condition
becomes true anytime that any one of the
selected bits become true.
<Object Identifier> 1.3.6.1.4.1.1206.4.2.6.4.2.1.3
"
DEFVAL {onChange}
::= { eventLogConfigEntry 3 }eventConfigMode · mandatory
eventConfigMode OBJECT-TYPE
SYNTAX INTEGER { other (1),
onChange (2),
greaterThanValue (3),
smallerThanValue (4),
hysteresisBound (5),
periodic (6),
andedWithValue (7) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"<Definition>This object specifies the mode of operation for
this event. The modes are defined as follows:
Value Description
other the event mode of operation is not
described in this standard, refer to the
device manual.
onChange create a log entry when the object value
referenced by eventConfigCompareOID
changes. The values of
eventConfigCompareValue and
eventConfigCompareValue2 are ignored in
this mode.
greaterThanValue create a log entry when the object value
referenced by eventConfigCompareOID
becomes greater than the value of
eventConfigCompareValue for the time
(tenth seconds) defined by
eventConfigCompareValue2 (zero means
immediate logging).
smallerThanValue create a log entry when the object value
referenced by eventConfigCompareOID
becomes less than the value of
eventConfigCompareValue for the time
(tenth seconds) defined by
eventConfigCompareValue2 (zero means
immediate logging).
hysteresisBound create a log entry when the object value
referenced by eventConfigCompareOID
becomes less than or greater than the
bound values. The lowerbound value is the
lower value of eventConfigCompareValue and
eventConfigCompareValue2; the upperbound
value is the higher value of the two values.
When the object value becomes greater than
the upper bound value, subsequent logging of
upperbound conditions shall not occur until
the object value becomes less than the
lower bound value.
When the object value becomes less than
the lower bound value, subsequent logging
of lowerbound conditions shall not occur
until the object value becomes greater
than the upper bound value.
periodic create a log entry every x seconds, where
x is defined by the value stored in
eventConfigCompareValue. The values stored
in eventConfigCompareValue2 and
eventConfigCompareOID are ignored in this
mode.
andedWithValue create a log entry when the object value
referenced by eventConfigCompareOID ANDED
with the value of eventConfigCompareValue
is NOT equal to zero for the time (tenth
seconds) defined by eventConfigCompareValue2
(zero means immediate logging). This allows
monitoring of a specific bit; the condition
becomes true anytime that any one of the
selected bits become true.
<Object Identifier> 1.3.6.1.4.1.1206.4.2.6.4.2.1.3
"
DEFVAL {onChange}
::= { eventLogConfigEntry 3 }eventConfigMode · deprecated
eventConfigMode OBJECT-TYPE
SYNTAX INTEGER { other (1),
onChange (2),
greaterThanValue (3),
smallerThanValue (4),
hysteresisBound (5),
periodic (6),
andedWithValue (7) }
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"<Definition>This object specifies the mode of operation for this event.
<Format> The modes are defined as follows:
Value Description
other the event mode of operation is not
described in this standard, refer to the
device manual.
onChange create a log entry when the object value
referenced by eventConfigCompareOID
changes. The values of
eventConfigCompareValue and
eventConfigCompareValue2 are ignored in
this mode.
greaterThanValue create a log entry when the object value
referenced by eventConfigCompareOID
becomes greater than the value of
eventConfigCompareValue for the time
(tenth seconds) defined by
eventConfigCompareValue2 (zero means
immediate logging).
smallerThanValue create a log entry when the object value
referenced by eventConfigCompareOID
becomes less than the value of
eventConfigCompareValue for the time
(tenth seconds) defined by
eventConfigCompareValue2 (zero means
immediate logging).
hysteresisBound create a log entry when the object value
referenced by eventConfigCompareOID
becomes less than or greater than the
bound values. The lowerbound value is the
lower value of eventConfigCompareValue and
eventConfigCompareValue2; the upperbound
value is the higher value of the two values.
When the object value becomes greater than
the upper bound value, subsequent logging of
upperbound conditions shall not occur until
the object value becomes less than the
lower bound value.
When the object value becomes less than
the lower bound value, subsequent logging
of lowerbound conditions shall not occur
until the object value becomes greater
than the upper bound value.
Periodic create a log entry every x seconds, where
x is defined by the value stored in
eventConfigCompareValue. The values stored
in eventConfigCompareValue2 and
eventConfigCompareOID are ignored in this
mode.
andedWithValue create a log entry when the object value
referenced by eventConfigCompareOID ANDED
with the value of eventConfigCompareValue
is NOT equal to zero for the time (tenth
seconds) defined by eventConfigCompareValue2
(zero means immediate logging). This allows
monitoring of a specific bit; the condition
becomes true anytime that any one of the
selected bits become true.
<Supplanted by> ISO26048-1-CondTrigger.fdCondTriggerMode (ISO 26048-1)
<Informative> The replacement object adds the following modes: - equal -
not equal - on creation (i.e., creation of a new row in a table) - on
deletion - separate modes for octet string and integer bitwise operations
<Object Identifier> 1.3.6.1.4.1.1206.4.2.6.4.2.1.3"
DEFVAL { onChange }
::= { eventLogConfigEntry 3 }eventConfigMode · deprecated
eventConfigMode OBJECT-TYPE
SYNTAX INTEGER { other (1),
onChange (2),
greaterThanValue (3),
smallerThanValue (4),
hysteresisBound (5),
periodic (6),
andedWithValue (7) }
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"<Definition>This object specifies the mode of operation for
this event.
<Format> The modes are defined as follows:
Value Description
other the event mode of operation is not
described in this standard, refer to the
device manual.
onChange create a log entry when the object value
referenced by eventConfigCompareOID
changes. The values of
eventConfigCompareValue and
eventConfigCompareValue2 are ignored in
this mode.
greaterThanValue create a log entry when the object value
referenced by eventConfigCompareOID
becomes greater than the value of
eventConfigCompareValue for the time
(tenth seconds) defined by
eventConfigCompareValue2 (zero means
immediate logging).
smallerThanValue create a log entry when the object value
referenced by eventConfigCompareOID
becomes less than the value of
eventConfigCompareValue for the time
(tenth seconds) defined by
eventConfigCompareValue2 (zero means
immediate logging).
hysteresisBound create a log entry when the object value
referenced by eventConfigCompareOID
becomes less than or greater than the
bound values. The lowerbound value is the
lower value of eventConfigCompareValue and
eventConfigCompareValue2; the upperbound
value is the higher value of the two values.
When the object value becomes greater than
the upper bound value, subsequent logging of
upperbound conditions shall not occur until
the object value becomes less than the
lower bound value.
When the object value becomes less than
the lower bound value, subsequent logging
of lowerbound conditions shall not occur
until the object value becomes greater
than the upper bound value.
Periodic create a log entry every x seconds, where
x is defined by the value stored in
eventConfigCompareValue. The values stored
in eventConfigCompareValue2 and
eventConfigCompareOID are ignored in this
mode.
andedWithValue create a log entry when the object value
referenced by eventConfigCompareOID ANDED
with the value of eventConfigCompareValue
is NOT equal to zero for the time (tenth
seconds) defined by eventConfigCompareValue2
(zero means immediate logging). This allows
monitoring of a specific bit; the condition
becomes true anytime that any one of the
selected bits become true.
<Superseded by> COND-TRIGGER-MIB.fdCondTriggerMode (ISO 20684-3)
<Informative> The replacement object adds the following modes:
- equal
- not equal
- on creation (i.e., creation of a new row in a table)
- on deletion
- separate modes for octet string and integer bitwise operations
<Object Identifier> 1.3.6.1.4.1.1206.4.2.6.4.2.1.3"
DEFVAL {onChange}
::= { eventLogConfigEntry 3 }eventConfigMode · mandatory
eventConfigMode OBJECT-TYPE
SYNTAX INTEGER { other (1),
onChange (2),
greaterThanValue (3),
smallerThanValue (4),
hysteresisBound (5),
periodic (6) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object specifies the mode of operation for this event. All checks and entries to the table must occur
within one second of the condition becoming true. The modes are defined as follows:
VALUE DESCRIPTION
onChange create a log entry when value referenced by the eventTypeOID changes
greaterThanValue create a log entry when the object value becomes greater than the value referenced
to by the eventCompareValue object, if this value is exceeded for the amount of time
specified in the eventConfigCompareValue2 object (in tenth of seconds) and this
value is greater than zero (0). A value of zero (0) for eventConfigCompareValue2
indicates immediate logging.
smallerThanValue create a log entry when the object value becomes less than the value referenced to by
the eventCompareValue object, if this value is exceeded for the amount of time
specified in the eventConfigCompareValue2 object (in tenth of seconds) and this
value is greater than zero (0). A value of zero (0) for eventConfigCompareValue2
indicates immediate logging.
hysteresisBound creates a log entry when the object value becomes either less than the lowerbound
value or greater than the upperbound value. The lowerbound value is the lower value
of the eventConfigCompareValue- and the eventConfigCompareValue2-objects, the
upperbound is the other value.
periodic create a log entry every x seconds, where x is defined by the value stored in
eventConfigCompareValue. The values stored in eventConfigCompareValue2 and
eventConfigCompareOID are ignored in this mode. "
::= { eventLogConfigEntry 3 }eventConfigMode · mandatory
eventConfigMode OBJECT-TYPE
SYNTAX INTEGER {
other (1),
onChange (2),
greaterThanValue (3),
smallerThanValue (4),
hysteresisBound (5),
periodic (6),
andedWithValue (7) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"<Definition>This object specifies the mode of operation for this event. The modes are defined as follows:
Value Description
other the event mode of operation is not described in this standard, refer to the device manual.
onChange create a log entry when the object value referenced by eventConfigCompareOID changes. The values of eventConfigCompareValue and eventConfigCompareValue2 are ignored in this mode.
greaterThanValue create a log entry when the object value referenced by eventConfigCompareOID becomes greater than the value of eventConfigCompareValue for the time (tenth seconds) defined by eventConfigCompareValue2 (zero means immediate logging).
smallerThanValue create a log entry when the object value referenced by eventConfigCompareOID becomes less than the value of eventConfigCompareValue for the time (tenth seconds) defined by eventConfigCompareValue2 (zero means immediate logging).
hysteresisBound create a log entry when the object value referenced by eventConfigCompareOID becomes less than or greater than the bound values. The lowerbound value is the lower value of eventConfigCompareValue and eventConfigCompareValue2; the upperbound value is the higher value of the two values.
When the object value becomes greater than the upper bound value, subsequent logging of upperbound conditions shall not occur until the object value becomes less than the lower bound value.
When the object value becomes less than the lower bound value, subsequent logging of lowerbound conditions shall not occur until the object value becomes greater than the upper bound value.
periodic create a log entry every x seconds, where x is defined by the value stored in eventConfigCompareValue. The values stored in eventConfigCompareValue2 and eventConfigCompareOID are ignored in this mode.
andedWithValue create a log entry when the object value referenced by eventConfigCompareOID ANDED with the value of eventConfigCompareValue is NOT equal to zero for the time (tenth seconds) defined by eventConfigCompareValue2 (zero means immediate logging). This allows monitoring of a specific bit; the condition becomes true anytime that any one of the selected bits become true.
<DescriptiveName>EventType.mode:code
<DataConceptType>Data Element"
DEFVAL {onChange}
::= { eventLogConfigEntry 3 }eventConfigMode · mandatory
eventConfigMode OBJECT-TYPE
SYNTAX INTEGER { other (1),
onChange (2),
greaterThanValue (3),
smallerThanValue (4),
hysteresisBound (5),
periodic (6),
andedWithValue (7) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"<Definition>This object specifies the mode of operation for this event. The modes are
defined as follows:
Value Description
other the event mode of operation is not described in this standard, refer to the
device manual.
onChange create a log entry when the object value referenced by
eventConfigCompareOID changes. The values of
eventConfigCompareValue and eventConfigCompareValue2 are ignored
in this mode.
greaterThanValue create a log entry when the object value referenced by
eventConfigCompareOID becomes greater than the value of
eventConfigCompareValue for the time (tenth seconds) defined by
eventConfigCompareValue2 (zero means immediate logging).
smallerThanValue create a log entry when the object value referenced by
eventConfigCompareOID becomes less than the value of
eventConfigCompareValue for the time (tenth seconds) defined by
eventConfigCompareValue2 (zero means immediate logging).
hysteresisBound create a log entry when the object value referenced by
eventConfigCompareOID becomes less than or greater than the bound
values. The lowerbound value is the lower value of
eventConfigCompareValue and eventConfigCompareValue2; the
upperbound value is the higher value of the two values.
When the object value becomes greater than the upper bound value,
subsequent logging of upperbound conditions shall not occur until the
object value becomes less than the lower bound value.
When the object value becomes less than the lower bound value,
subsequent logging of lowerbound conditions shall not occur until the
object value becomes greater than the upper bound value.
periodic create a log entry every x seconds, where x is defined by the value
stored in eventConfigCompareValue. The values stored in
eventConfigCompareValue2 and eventConfigCompareOID are ignored
in this mode.
andedWithValue create a log entry when the object value referenced by
eventConfigCompareOID ANDED with the value of
eventConfigCompareValue is NOT equal to zero for the time
(tenth seconds) defined by eventConfigCompareValue2 (zero
means immediate logging). This allows monitoring of a specific
bit; the condition becomes true anytime that any one of the
selected bits become true.
<DescriptiveName>EventType.mode:code
<DataConceptType>Data Element"
DEFVAL {onChange}
::= { eventLogConfigEntry 3 }eventConfigMode · mandatory
eventConfigMode OBJECT-TYPE
SYNTAX INTEGER { other (1),
onChange (2),
greaterThanValue (3),
smallerThanValue (4),
hysteresisBound (5),
periodic (6),
andedWithValue (7) }
ACCESS read-write
STATUS mandatory
DESCRIPTION
"<Definition>This object specifies the mode of operation for this
event. The modes are defined as follows:
Value Description
other the event mode of operation is not described in this
standard, refer to the device manual.
onChange create a log entry when the object value referenced by
eventConfigCompareOID changes. The values of
eventConfigCompareValue and eventConfigCompareValue2
are ignored in this mode.
greaterThanValue create a log entry when the object value referenced by
eventConfigCompareOID becomes greater than the value
of eventConfigCompareValue for the time (tenth
seconds) defined by eventConfigCompareValue2 (zero
means immediate logging).
smallerThanValue create a log entry when the object value referenced by
eventConfigCompareOID becomes less than the value of
eventConfigCompareValue for the time (tenth seconds)
defined by eventConfigCompareValue2 (zero means
immediate logging).
hysteresisBound create a log entry when the object value referenced by
eventConfigCompareOID becomes less than or greater
than the bound values. The lowerbound value is the
lower value of eventConfigCompareValue and
eventConfigCompareValue2; the upperbound value is the
higher value of the two values.
When the object value becomes greater than the
upper bound value, subsequent logging of
upperbound conditions shall not occur until the
object value becomes less than the lower bound
value.
When the object value becomes less than the
lower bound value, subsequent logging of
lowerbound conditions shall not occur until the
object value becomes greater than the upper
bound value.
periodic create a log entry every x seconds, where x is defined
by the value stored in eventConfigCompareValue. The
values stored in eventConfigCompareValue2 and
eventConfigCompareOID are ignored in this mode.
andedWithValue create a log entry when the object value
referenced by eventConfigCompareOID ANDED with
the value of eventConfigCompareValue is NOT
equal to zero for the time (tenth seconds)
defined by eventConfigCompareValue2 (zero means
immediate logging). This allows monitoring of a
specific bit; the condition becomes true anytime
that any one of the selected bits become true.
<DescriptiveName>EventType.mode:code
<DataConceptType>Data Element"
DEFVAL {onChange}
::= { eventLogConfigEntry 3 }