This attribute is not applicable and is ignored for CQC-based ATM
cards.
This attribute specifies the emission priority (EP) which is used to
transmit traffic of the ABR service category. A lower numerical
value for this attribute specifies a higher emission priority. 0 is the
highest EP and 7 is the lowest. Cells at a higher emission priority
receive higher preference for link bandwidth. EPs 0 and 1 are in the
absolute priority range, and are unaffected by any minimum
bandwidth guarantees. EPs 2 through 7 are in the guaranteed
bandwidth range. Minimum bandwidth guarantee is specified in the
AtmIf/n Ep/m component.
Emission priority setting must comply with all of the following
constraints:
1. The emission priority numbers must be in the following order:
CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR
2. Two different ATM service categories may share the same EP
only if they are both shaped.
3. CBR and rt-VBR may be placed either in the absolute priority
range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2
through 7).
4. If both CBR and rt-VBR are shaped, rt-VBR must share the
same EP with CBR or ABR. If either one of CBR or rt-VBR are
not shaped, then they cannot share the same EP.
5. ABR service category is always deemed to be shaped. If nrt-VBR
is shaped, it must share the same EP with ABR. If nrt-VBR is not
shaped it must have a higher EP than ABR.
6. If UBR is shaped, it must share the same EP with ABR. If UBR
is not shaped, it must have a lower EP than ABR.
This attribute does not apply to basic Vpts, and standard Vpt Vccs.
Parsed from file nortelPC-atmCoreV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
This attribute is not applicable and is ignored for CQC-based ATM
cards.
This attribute specifies the emission priority (EP) which is used to
transmit traffic of the ABR service category. A lower numerical
value for this attribute specifies a higher emission priority. 0 is the
highest EP and 7 is the lowest. Cells at a higher emission priority
receive higher preference for link bandwidth. EPs 0 and 1 are in the
absolute priority range, and are unaffected by any minimum
bandwidth guarantees. EPs 2 through 7 are in the guaranteed
bandwidth range. Minimum bandwidth guarantee is specified in the
AtmIf/n Ep/m component.
Emission priority setting must comply with all of the following
constraints:
1. The emission priority numbers must be in the following order:
CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR
2. Two different ATM service categories may share the same EP
only if they are both shaped.
3. CBR and rt-VBR may be placed either in the absolute priority
range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2
through 7).
4. If both CBR and rt-VBR are shaped, rt-VBR must share the
same EP with CBR or ABR. If either one of CBR or rt-VBR are
not shaped, then they cannot share the same EP.
5. ABR service category is always deemed to be shaped. If nrt-VBR
is shaped, it must share the same EP with ABR. If nrt-VBR is not
shaped it must have a higher EP than ABR.
6. If UBR is shaped, it must share the same EP with ABR. If UBR
is not shaped, it must have a lower EP than ABR.
This attribute does not apply to basic Vpts, and standard Vpt Vccs.
Parsed from file Nortel-MsCarrier-MscPassport-AtmCoreMIB.mib
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
[Automatically extracted from oidview.com]
mscAtmIfCAAbrEmissionPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) which is used to transmit traffic of the ABR service category. A lower numerical value for this attribute specifies a higher emission priority. 0 is the highest EP and 7 is the lowest. Cells at a higher emission priority receive higher preference for link bandwidth. EPs 0 and 1 are in the absolute priority range, and are unaffected by any minimum bandwidth guarantees. EPs 2 through 7 are in the guaranteed bandwidth range. Minimum bandwidth guarantee is specified in the AtmIf/n Ep/m component. Emission priority setting must comply with all of the following constraints: 1. The emission priority numbers must be in the following order: CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR 2. Two different ATM service categories may share the same EP only if they are both shaped. 3. CBR and rt-VBR may be placed either in the absolute priority range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2 through 7). 4. If both CBR and rt-VBR are shaped, rt-VBR must share the same EP with CBR or ABR. If either one of CBR or rt-VBR are not shaped, then they cannot share the same EP. 5. ABR service category is always deemed to be shaped. If nrt-VBR is shaped, it must share the same EP with ABR. If nrt-VBR is not shaped it must have a higher EP than ABR. 6. If UBR is shaped, it must share the same EP with ABR. If UBR is not shaped, it must have a lower EP than ABR. This attribute does not apply to basic Vpts, and standard Vpt Vccs." DEFVAL { 6 } ::= { mscAtmIfCAAbrProvEntry 15 }
mscAtmIfCAAbrEmissionPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) which is used to transmit traffic of the ABR service category. A lower numerical value for this attribute specifies a higher emission priority. 0 is the highest EP and 7 is the lowest. Cells at a higher emission priority receive higher preference for link bandwidth. EPs 0 and 1 are in the absolute priority range, and are unaffected by any minimum bandwidth guarantees. EPs 2 through 7 are in the guaranteed bandwidth range. Minimum bandwidth guarantee is specified in the AtmIf/n Ep/m component. Emission priority setting must comply with all of the following constraints: 1. The emission priority numbers must be in the following order: CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR 2. Two different ATM service categories may share the same EP only if they are both shaped. 3. CBR and rt-VBR may be placed either in the absolute priority range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2 through 7). 4. If both CBR and rt-VBR are shaped, rt-VBR must share the same EP with CBR or ABR. If either one of CBR or rt-VBR are not shaped, then they cannot share the same EP. 5. ABR service category is always deemed to be shaped. If nrt-VBR is shaped, it must share the same EP with ABR. If nrt-VBR is not shaped it must have a higher EP than ABR. 6. If UBR is shaped, it must share the same EP with ABR. If UBR is not shaped, it must have a lower EP than ABR. This attribute does not apply to basic Vpts, and standard Vpt Vccs." DEFVAL { 6 } ::= { mscAtmIfCAAbrProvEntry 15 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.10 | mscAtmIfCAAbrPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the available bit rate (ABR) service category except … |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.11 | mscAtmIfCAAbrCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the ABR service category. An ov… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.12 | mscAtmIfCAAbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the ABR service c… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.13 | mscAtmIfCAAbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the ABR service category. The queue lim… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.14 | mscAtmIfCAAbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the AB… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.19 | mscAtmIfCAAbrFairnessPolicy | 0 | 0 | This attribute specifies the fairness policy which is applied to available bandwidth when performing the ER calculation in the AB… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.20 | mscAtmIfCAAbrFrttPortion | 0 | 0 | This attribute specifies the portion of the Fixed Round Trip Time (FRTT) which is added to each ABR call setup which traverses t… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.21 | mscAtmIfCAAbrAbrConnectionType | 0 | 0 | This attribute specifies the default type for ABR connections. It may be overridden by the abrConnectionType attribute under the… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.22 | mscAtmIfCAAbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the ABR service category. An overri… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.23 | mscAtmIfCAAbrInitialCellRate | 0 | 0 | This attribute specifies the default Initial Cell Rate (ICR) parameter for ABR connections. An override to this default may be s… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.24 | mscAtmIfCAAbrRateDecreaseFactor | 0 | 0 | This attribute specifies the default Rate Decrease Factor (RDF) for ABR connections. An override to this default may be specifie… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.25 | mscAtmIfCAAbrRateIncreaseFactor | 0 | 0 | This attribute specifies the default Rate Increase Factor (RIF) for ABR connections. An override to this default may be specifie… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.26 | mscAtmIfCAAbrMaxCellPerRmCell | 0 | 0 | This attribute specifies the default number of user cells per Resource Management cell (NRM) for ABR connections. An override to … |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.27 | mscAtmIfCAAbrMaxTimeBetweenRmCell | 0 | 0 | This attribute specifies the default time between Resource Management cells (TRM) for ABR connections. An override to this defaul… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.28 | mscAtmIfCAAbrCutoffDecreaseFactor | 0 | 0 | This attribute specifies the default Cutoff Decrease Factor (CDF) parameter for ABR connections. An override to this default may… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.29 | mscAtmIfCAAbrAcrDecreaseTimeFactor | 0 | 0 | This attribute specifies the default Allowed Cell Rate Decrease Time Factor (ADTF) parameter for ABR connections. An override to … |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.30 | mscAtmIfCAAbrDgcraMaximumDelay | 0 | 0 | This attribute specifies the default maximum delay for Dynamic General Cell Rate Algorithm (DGCRA) rate changes for ABR connectio… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.31 | mscAtmIfCAAbrDgcraMinimumDelay | 0 | 0 | This attribute specifies the default minimum delay for Dynamic General Cell Rate Algorithm (DGCRA) rate changes for ABR connectio… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.32 | mscAtmIfCAAbrHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVP and SVC ABR connections. It takes a value from 0 (hig… |