This attribute specifies the default minimum delay for Dynamic
General Cell Rate Algorithm (DGCRA) rate changes for ABR
connections. An override to this default may be specified for a
provisioned connection under the Vcd Tm Abr or Vpd Tm Abr
component.
This attribute specifies a lower bound on the delay after which the
rate change induced by a backward Resource Management (B-RM)
cell departing from this interface (in the backward direction) is
expected to be observed at the interface (in the forward connection).
This lower bound may be approximated as the round trip sum of the
fixed and propagation delays between the ABR source and this
interface.
The value of this attribute is used in policing an ABR connection
using the DGCRA. A smaller value for this attribute implies a more
lenient policer. When there is an increase in the Allowed Cell Rate
(ACR), the policer waits for a correspondingly shorter period of
time before it enforces the new cell rate.
The value of this attribute must be less than or equal to
dgcraMaximumDelay, since the maximum delay must be greater
than or equal to the minimum delay.
Parsed from file nortelPC-atmCoreV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
This attribute specifies the default minimum delay for Dynamic
General Cell Rate Algorithm (DGCRA) rate changes for ABR
connections. An override to this default may be specified for a
provisioned connection under the Vcd Tm Abr or Vpd Tm Abr
component.
This attribute specifies a lower bound on the delay after which the
rate change induced by a backward Resource Management (B-RM)
cell departing from this interface (in the backward direction) is
expected to be observed at the interface (in the forward connection).
This lower bound may be approximated as the round trip sum of the
fixed and propagation delays between the ABR source and this
interface.
The value of this attribute is used in policing an ABR connection
using the DGCRA. A smaller value for this attribute implies a more
lenient policer. When there is an increase in the Allowed Cell Rate
(ACR), the policer waits for a correspondingly shorter period of
time before it enforces the new cell rate.
The value of this attribute must be less than or equal to
dgcraMaximumDelay, since the maximum delay must be greater
than or equal to the minimum delay.
Parsed from file Nortel-MsCarrier-MscPassport-AtmCoreMIB.mib
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
[Automatically extracted from oidview.com]
mscAtmIfCAAbrDgcraMinimumDelay OBJECT-TYPE SYNTAX Unsigned32 (1..16700000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default minimum delay for Dynamic General Cell Rate Algorithm (DGCRA) rate changes for ABR connections. An override to this default may be specified for a provisioned connection under the Vcd Tm Abr or Vpd Tm Abr component. This attribute specifies a lower bound on the delay after which the rate change induced by a backward Resource Management (B-RM) cell departing from this interface (in the backward direction) is expected to be observed at the interface (in the forward connection). This lower bound may be approximated as the round trip sum of the fixed and propagation delays between the ABR source and this interface. The value of this attribute is used in policing an ABR connection using the DGCRA. A smaller value for this attribute implies a more lenient policer. When there is an increase in the Allowed Cell Rate (ACR), the policer waits for a correspondingly shorter period of time before it enforces the new cell rate. The value of this attribute must be less than or equal to dgcraMaximumDelay, since the maximum delay must be greater than or equal to the minimum delay." DEFVAL { 1 } ::= { mscAtmIfCAAbrProvEntry 31 }
mscAtmIfCAAbrDgcraMinimumDelay OBJECT-TYPE SYNTAX Unsigned32 (1..16700000) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default minimum delay for Dynamic General Cell Rate Algorithm (DGCRA) rate changes for ABR connections. An override to this default may be specified for a provisioned connection under the Vcd Tm Abr or Vpd Tm Abr component. This attribute specifies a lower bound on the delay after which the rate change induced by a backward Resource Management (B-RM) cell departing from this interface (in the backward direction) is expected to be observed at the interface (in the forward connection). This lower bound may be approximated as the round trip sum of the fixed and propagation delays between the ABR source and this interface. The value of this attribute is used in policing an ABR connection using the DGCRA. A smaller value for this attribute implies a more lenient policer. When there is an increase in the Allowed Cell Rate (ACR), the policer waits for a correspondingly shorter period of time before it enforces the new cell rate. The value of this attribute must be less than or equal to dgcraMaximumDelay, since the maximum delay must be greater than or equal to the minimum delay." DEFVAL { 1 } ::= { mscAtmIfCAAbrProvEntry 31 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.10 | mscAtmIfCAAbrPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the available bit rate (ABR) service category except … |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.11 | mscAtmIfCAAbrCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the ABR service category. An ov… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.12 | mscAtmIfCAAbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the ABR service c… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.13 | mscAtmIfCAAbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the ABR service category. The queue lim… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.14 | mscAtmIfCAAbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the AB… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.15 | mscAtmIfCAAbrEmissionPriority | 0 | 0 | This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) whi… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.19 | mscAtmIfCAAbrFairnessPolicy | 0 | 0 | This attribute specifies the fairness policy which is applied to available bandwidth when performing the ER calculation in the AB… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.20 | mscAtmIfCAAbrFrttPortion | 0 | 0 | This attribute specifies the portion of the Fixed Round Trip Time (FRTT) which is added to each ABR call setup which traverses t… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.21 | mscAtmIfCAAbrAbrConnectionType | 0 | 0 | This attribute specifies the default type for ABR connections. It may be overridden by the abrConnectionType attribute under the… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.22 | mscAtmIfCAAbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the ABR service category. An overri… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.23 | mscAtmIfCAAbrInitialCellRate | 0 | 0 | This attribute specifies the default Initial Cell Rate (ICR) parameter for ABR connections. An override to this default may be s… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.24 | mscAtmIfCAAbrRateDecreaseFactor | 0 | 0 | This attribute specifies the default Rate Decrease Factor (RDF) for ABR connections. An override to this default may be specifie… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.25 | mscAtmIfCAAbrRateIncreaseFactor | 0 | 0 | This attribute specifies the default Rate Increase Factor (RIF) for ABR connections. An override to this default may be specifie… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.26 | mscAtmIfCAAbrMaxCellPerRmCell | 0 | 0 | This attribute specifies the default number of user cells per Resource Management cell (NRM) for ABR connections. An override to … |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.27 | mscAtmIfCAAbrMaxTimeBetweenRmCell | 0 | 0 | This attribute specifies the default time between Resource Management cells (TRM) for ABR connections. An override to this defaul… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.28 | mscAtmIfCAAbrCutoffDecreaseFactor | 0 | 0 | This attribute specifies the default Cutoff Decrease Factor (CDF) parameter for ABR connections. An override to this default may… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.29 | mscAtmIfCAAbrAcrDecreaseTimeFactor | 0 | 0 | This attribute specifies the default Allowed Cell Rate Decrease Time Factor (ADTF) parameter for ABR connections. An override to … |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.30 | mscAtmIfCAAbrDgcraMaximumDelay | 0 | 0 | This attribute specifies the default maximum delay for Dynamic General Cell Rate Algorithm (DGCRA) rate changes for ABR connectio… |
| 1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.32 | mscAtmIfCAAbrHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVP and SVC ABR connections. It takes a value from 0 (hig… |