This attribute specifies the fairness policy which is applied to
available bandwidth when performing the ER calculation in the
ABR service category. This applies to any connection point
performing explicit rate calculations. Each ABR connection is
assigned a weight. Connections with a higher weight get a greater
proportion of the available ABR bandwidth compared with
connections that have lower weights. This attribute is ignored on
CQC-based ATM cards.
If the value is mcr, the congestion fairness weight is based on the
Minimum Cell Rate (MCR) of the connection.
If the value is pcr, the congestion fairness weight is based on the
Peak Cell Rate (PCR) of the connection.
If the value is pcrMinusMcr, the congestion fairness weight is
based on the difference between the Peak Cell Rate and the
Minimum Cell Rate (PCR - MCR) of the connection.
Parsed from file nortelPC-atmCoreV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
This attribute specifies the fairness policy which is applied to
available bandwidth when performing the ER calculation in the
ABR service category. This applies to any connection point
performing explicit rate calculations. Each ABR connection is
assigned a weight. Connections with a higher weight get a greater
proportion of the available ABR bandwidth compared with
connections that have lower weights. This attribute is ignored on
CQC-based ATM cards.
If the value is mcr, the congestion fairness weight is based on the
Minimum Cell Rate (MCR) of the connection.
If the value is pcr, the congestion fairness weight is based on the
Peak Cell Rate (PCR) of the connection.
If the value is pcrMinusMcr, the congestion fairness weight is
based on the difference between the Peak Cell Rate and the
Minimum Cell Rate (PCR - MCR) of the connection.
Parsed from file Nortel-MsCarrier-MscPassport-AtmCoreMIB.mib
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-AtmCoreMIB
[Automatically extracted from oidview.com]
mscAtmIfCAAbrFairnessPolicy OBJECT-TYPE SYNTAX INTEGER { mcr(0), pcr(2), pcrMinusMcr(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the fairness policy which is applied to available bandwidth when performing the ER calculation in the ABR service category. This applies to any connection point performing explicit rate calculations. Each ABR connection is assigned a weight. Connections with a higher weight get a greater proportion of the available ABR bandwidth compared with connections that have lower weights. This attribute is ignored on CQC-based ATM cards. If the value is mcr, the congestion fairness weight is based on the Minimum Cell Rate (MCR) of the connection. If the value is pcr, the congestion fairness weight is based on the Peak Cell Rate (PCR) of the connection. If the value is pcrMinusMcr, the congestion fairness weight is based on the difference between the Peak Cell Rate and the Minimum Cell Rate (PCR - MCR) of the connection." DEFVAL { pcrMinusMcr } ::= { mscAtmIfCAAbrProvEntry 19 }
mscAtmIfCAAbrFairnessPolicy OBJECT-TYPE SYNTAX INTEGER { mcr(0), pcr(2), pcrMinusMcr(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the fairness policy which is applied to available bandwidth when performing the ER calculation in the ABR service category. This applies to any connection point performing explicit rate calculations. Each ABR connection is assigned a weight. Connections with a higher weight get a greater proportion of the available ABR bandwidth compared with connections that have lower weights. This attribute is ignored on CQC-based ATM cards. If the value is mcr, the congestion fairness weight is based on the Minimum Cell Rate (MCR) of the connection. If the value is pcr, the congestion fairness weight is based on the Peak Cell Rate (PCR) of the connection. If the value is pcrMinusMcr, the congestion fairness weight is based on the difference between the Peak Cell Rate and the Minimum Cell Rate (PCR - MCR) of the connection." DEFVAL { pcrMinusMcr } ::= { mscAtmIfCAAbrProvEntry 19 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.10 | mscAtmIfCAAbrPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the available bit rate (ABR) service category except … |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.11 | mscAtmIfCAAbrCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the ABR service category. An ov… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.12 | mscAtmIfCAAbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the ABR service c… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.13 | mscAtmIfCAAbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the ABR service category. The queue lim… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.14 | mscAtmIfCAAbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the AB… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.15 | mscAtmIfCAAbrEmissionPriority | 0 | 0 | This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) whi… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.20 | mscAtmIfCAAbrFrttPortion | 0 | 0 | This attribute specifies the portion of the Fixed Round Trip Time (FRTT) which is added to each ABR call setup which traverses t… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.21 | mscAtmIfCAAbrAbrConnectionType | 0 | 0 | This attribute specifies the default type for ABR connections. It may be overridden by the abrConnectionType attribute under the… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.22 | mscAtmIfCAAbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the ABR service category. An overri… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.23 | mscAtmIfCAAbrInitialCellRate | 0 | 0 | This attribute specifies the default Initial Cell Rate (ICR) parameter for ABR connections. An override to this default may be s… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.24 | mscAtmIfCAAbrRateDecreaseFactor | 0 | 0 | This attribute specifies the default Rate Decrease Factor (RDF) for ABR connections. An override to this default may be specifie… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.25 | mscAtmIfCAAbrRateIncreaseFactor | 0 | 0 | This attribute specifies the default Rate Increase Factor (RIF) for ABR connections. An override to this default may be specifie… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.26 | mscAtmIfCAAbrMaxCellPerRmCell | 0 | 0 | This attribute specifies the default number of user cells per Resource Management cell (NRM) for ABR connections. An override to … |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.27 | mscAtmIfCAAbrMaxTimeBetweenRmCell | 0 | 0 | This attribute specifies the default time between Resource Management cells (TRM) for ABR connections. An override to this defaul… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.28 | mscAtmIfCAAbrCutoffDecreaseFactor | 0 | 0 | This attribute specifies the default Cutoff Decrease Factor (CDF) parameter for ABR connections. An override to this default may… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.29 | mscAtmIfCAAbrAcrDecreaseTimeFactor | 0 | 0 | This attribute specifies the default Allowed Cell Rate Decrease Time Factor (ADTF) parameter for ABR connections. An override to … |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.30 | mscAtmIfCAAbrDgcraMaximumDelay | 0 | 0 | This attribute specifies the default maximum delay for Dynamic General Cell Rate Algorithm (DGCRA) rate changes for ABR connectio… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.31 | mscAtmIfCAAbrDgcraMinimumDelay | 0 | 0 | This attribute specifies the default minimum delay for Dynamic General Cell Rate Algorithm (DGCRA) rate changes for ABR connectio… |
1.3.6.1.4.1.562.36.2.1.114.3.5.100.1.32 | mscAtmIfCAAbrHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVP and SVC ABR connections. It takes a value from 0 (hig… |